10641512100 Kenmore Refrigerator - Instructions

First of all the part was not located in the section of the refrigerator that was shown in the video. I wasted a lot of time taking that section apart only to find that the part wasn't there. After some investigation I finally located the defective part. It was behind a piece of sheet metal that had to be bent out of the way to unscrew the part. If I hadn't bent it out of the way, it would have been a major disassembly to remove the sheet metal. Once removed, the installation of the new part was fairly simple. The only confusing thing about the installation was determinig which of the prongs on the part that the internal wire to the new part was to be attached. There were 3 options given and the instructions were not very clear as to which one I should use. Apparently I guessed correctly because the refrigerator seems to be functioning perfectly since the repair.

Removed old drawer, replaced with new one. Easy fix. New drawer fits perfect.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

The glass cover came on time and in good packaging. I removed it from the packaging and slipped in to the shelf. It fit perfectly and was extremely easy to do. We are very pleased with the entire process. Thanks

Fan was barely rotating. So unplugged, removed back cover, removed fan and motor from frame work. Removed fan blade from motor shaft. Spun motor shaft which seemed fine. Pryed off back cover of motor to find a large but dry felt washer and a helical capillery slot formed into the motor shaft for carring oil from felt washer to the bearings. Added 30 wt motor oil and some 3in1 oil to felt and reassembled motor, fan and frame work. Plugged in power chord after getting rid of dust and dog hear on coils and is working like new.

Removed refrig. door and replaced closing cam and tightened the bottom cam

Fridge would stop cooling, get way over temperature. I noticed it would start up again if I tapped near the thermostat. It would run for a while then stop again. Replaced the thermostat exactly as shown in video. Fridge works fine now.

all is fine now. thanks andy

I just slid the old one out and slid the replacement in. Although PartSelect warned that the item was a substitute for the original drawer model, the crisper drawer supplied seemed identical to the original to me. I couldn't be more pleased.

watched the video followed the instructions and the repair took less than 30 mins. thank you parts plus for the video ref now workes properly and saved me a bundle of money

Installation went smooth - only three hex-head screws (one below unit and two above. After removing 3 screws, unit comes loose in your hand but is still connected by a plug leading 4 wires to a connector visible through a slot in back panel of freezer compartment. New unit goes in easily (making sure spout from pump that protrudes from back wall fits through opening on icemaker) but there's not a generous amout of wiring harness and the 'female' of the electrical connection is recessed and loose inside a cutout in the rear panel so you can't get a good grip on it nor can you feel if it plugs securely. I plugged new unit into connector and then secured it with the 3 screws, waited the 12 hours per instructions, but no ice. Removed unit and guessed that the plug had not seated fully (not plugged in.) I took a short piece of a wooden paint stirrer and put it on back edge of plug and tapped it into place so it seated fully. Immediately, the pump cycled and water came from the filler spout, so I surmised that it was now properly plugged in - it began making ice in a couple of hours and has operated perfectly ever since. Lesson learned is to make sure you get the electrical connector fully in place - mine did not 'snap' or 'click' into place and I wrongly assumed it was plugged in correctly.

I opened the box. That was the hardest part. I slid in the new drawer. I was a little distressed that my model # was not listed, but the pictures on your site were very helpful. Thanks

First, removed the top hinge (3 screws), then lifted the door off the bottom hinge. Replaced the Cam on the bottom of the door and then the Cam on the bottom hinge (one screw for each). Placed the door back on the bottom hinge, reinsert the top hinge into the door and secure top hinge to the refrig with the 3 screws original removed. EASY!!

After ordering the ice-maker, but before it had arrived, I installed a valve in the pex water line in the room right below the fridge. I had to rent a pex clamp kit from Home Depot. It cost $8 for 4 hours and came with the crimpers and band cutters. I then ran a poly line to an in-line filter which I mounted to an exposed stud and fished the line up the wall and out a small hole I drilled behind the fridge. When the ice-maker came, it took less than 30 minutes to install and start my first batch of ice. With the in-line filter, the ice forms with practically no sediment flakes. Part Select was the only place I could find a replacement ice-maker. In addition to the parts in the ice-maker kit, I had to buy 12 feet of poly water line, a ball-valve, the in-line filter and a compression fitting. A total of $20 at my plumbing contractor store.

I just simply eliminated the ice buildup with hot water and a knife. But I still have the Defrost Timer Kit for future use.