106106-8130660 Kenmore Refrigerator - Instructions

After searching online to diagnose the issue with my refrigerator being warm and the freezer being cold and not shutting off to defrost I decided to get the defrost timer kit. The kit arrived within 2 day. With the directions included, after unplugging the appliance for safety, I installed it relatively quickly with only a screwdriver . I then plugged it back in and it immediately went to defrost. I thought, wow I have it fixed. Well unbeknownst to me it still didn't cool in the fridge area. After doing more internet research I found a suggestion to unplug the fridge for 24 hours to unthaw ice that may be lodged between the freezer and fridge that is blocking the distribution of cold air into the fridge. After doing this, it now works like a charm.

I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.

I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.

removed old and instaslled new. biggest problem was getting to one of the screws.

I removed one bolt and took out the old roller after first blocking up the fridge. Then I was puzzled for a moment because the hole in the new assembly was not tapped. But then I saw that the old bolt was a self tapping bolt. I used it to tap the hole then removed it and installed the new assembly. No sweat job.

Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

Followed instructions from ideoo

Pull refrigerator out to access back, unplug unit and remove the 3 .25" screws cut the power leads to motor and install new with easy to understand instructions provided with new motor. Plug refrigerator back in and enjoy your cold beverages once more. EASIEST REPAIR EVER.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

Followed video and had one problen, the metal pipe would not release as shown,so I used a hacksaw between the plastic and metal pipe, removing the metal pipe from inside as the video shows. Good instructions.

Simple. 1st, removed broken part to understand part (water fill tube to freezer, plastic part at top of fill tube cracked). 2nd go on your web site and look at prints to find part number, Study video to understand video. 3rd. Called customer service and lady was very nice and efficient. Placed order and received. Study video again and installed. My 9 year old grandson was visiting from out of town and assisted in installation. Just over 30 minutes to install

Reviewed Youtube video as a reference. Unplugged refrigerator. Removed old defrost timer. Matched the color of the wiring harness to the diagram that came with the part. Attach new part to wiring harness.

Very easy. Left the front of the refrigerator so it is approx. 4 inches of the floor. (used a two by four. Removed the screws (one for each roller). Removed the rollers and replaced with new rollers. Reinstalled the screws with secures the rollers to the refrigerator. Done

Unplug refrigerator.
Pry switch out with putty knife
Remove two wires from switch
Attach wires to new switch
Push new switch into slot