Maytag Dishwasher Pumps

Find Your Part

Model number locator Need help finding your model number?
  • Search your model number to find:
  • Genuine OEM parts guaranteed to fit
  • Free manuals and guides
  • Repair instructions and videos
Maytag Appliance Parts
Shop By Part Type

Popular Maytag Dishwasher Pumps

Videos!
Your Price
$91.96
  In Stock
Maytag Dishwasher Drain Pump
★★★★★
★★★★★
57 Reviews
PartSelect Number PS11753379
Manufacturer Part Number WPW10348269
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Andrew from Alexandria, VA
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.

First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done. Read more...
Your Price
$105.46
  In Stock
Maytag Dishwasher Drain Pump
★★★★★
★★★★★
14 Reviews
PartSelect Number PS11738151
Manufacturer Part Number W10876537
This drain pump is for dishwashers. Drain pump removes the water from the dishwasher tub during the drain phase of the dishwashing cycle. Unplug the dishwasher and shut off the water supply before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
Installation Instructions
Kelli from BURLINGTON, MA
Dish washer would not drain properly
Shut off breaker. Took off front skirt of dishwasher .
Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn and push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front. Read more...
Your Price
$69.06
  In Stock
Maytag Dishwasher Drain Pump
★★★★★
★★★★★
5 Reviews
PartSelect Number PS11756031
Manufacturer Part Number WPW10531320
Fixes these symptoms
Installation Instructions
Paul from CANONSBURG, PA
Drain pump flange broke
Laid on my side amd reach under unit Read more...
Videos!
Your Price
$222.51
  In Stock
Maytag Dishwasher Circulation Pump and Motor
★★★★★
★★★★★
22 Reviews
PartSelect Number PS11757388
Manufacturer Part Number WPW10757217
The circulation pump and motor is located near the bottom of the dishwasher. The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle. Before you begin this repair, it is recommended that you pull your dishwasher out of the cabinet, so you can tip the dishwasher to one side and gain better access to the circulation pump and motor. Be sure to disconnect the power source and the water source to the dishwasher before you begin this repair. To complete this repair you will need a 1/4 inch nut driver and a 3/8 inch nut driver.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Steve from Inver Grove Heights, MN
Loud grinding noise from water pump
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now. Read more...
Videos!
Your Price
$109.17
  In Stock
Maytag Dishwasher Drain and Wash Impeller Kit
★★★★★
★★★★★
18 Reviews
PartSelect Number PS382822
Manufacturer Part Number 675806
This dishwasher drain and wash impeller kit comes with both the drain and wash impeller, gaskets, chopper, and installation screw. This part helps stop your dishwasher from leaking and helps with the proper draining of the dishwasher. If you notice that your dishes are not cleaning, the dishwasher is not draining properly, or is making any unusually loud sounds or grinding noises, this could indicate the impeller and seal kit have broken down and need to be replaced. You will need a #15 and #20 torx driver, a small flat-blade screwdriver, 1/4-inch nut driver, adjustable wrench, and a small hammer and a sharp chisel.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Daniel from Sarasota, FL
leaking from tub above motor
Disconnect unit and remove from under counter. remove lower spray arm, tip over dishwasher on it's back, diconnect wires from motor , unscrew drain fitting rotate motor mounts to and lift pump and motor assembly up and out from inside the dishwasher. thoughly clean all parts during pump disassembly( under running water and a toothbrush works well) . Looking at a parts diagram,and using your memory from disassembly replace the new seals and put it all back together, with patience you can do anything and use common sense. Read more...
Your Price
$124.86
  In Stock
Maytag Dishwasher Sump
★★★★★
★★★★★
7 Reviews
PartSelect Number PS11755006
Manufacturer Part Number WPW10455268
This works in conjunction with the pump and filtration system. It is used to receive drainage for disposal.
Fixes these symptoms
Installation Instructions
Jason from MOLINE, IL
Water leaking through the sump shaft seal
First I removed everything off of the bottom of the dishwasher. Then I removed the main center piece that everything mounts to. Then I reinstalled the new center piece with the help of some evoo cooking spray (extra virgin olive oil) I sprayed it on the rubber seal to aid in getting that center piece installed without a battle. Then I reinstalled everything else in the reverse order that I removed it. The evoo cooking spray works wonders for more than just cooking !!! Read more...
Videos!
Your Price
$126.09
  In Stock
Maytag Dishwasher Accumulator and Filter
★★★★★
★★★★★
5 Reviews
PartSelect Number PS897295
Manufacturer Part Number 8193918
This part is essential in your dishes getting clean during the wash cycle. If there is any debris or a tear in the filter, it can cause extra buildup and, therefore, causing dirty dishes.
Fixes these symptoms
Installation Instructions
Ashok from CHAPEL HILL, NC
Dishes did not always clean with some residue left on the dishes. Needed to replace the filter
Just followed the YouTube video they sent with the receipt. Read more...
Videos!
Your Price
$94.51
  In Stock
Maytag Dishwasher Impeller
★★★★★
★★★★★
3 Reviews
PartSelect Number PS12069388
Manufacturer Part Number 8193951A
This is the replacement impeller kit for your dishwasher. This impeller kit comes with 4 pieces, including the impeller and seals which you will need for the repair. The impeller and seal kit is mounted on the dishwasher motor. If your dishwasher is not cleaning dishes properly, it may be an indication that your impeller has gone bad, and you are not getting proper water pressure. If the seals have gone bad, your dishwasher may start to leak. If you are having either of these problems, you may need to replace the impeller kit. Be sure to disconnect the water and power source from the dishwasher before you begin this repair. This is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Chauncey from Menan, ID
Started with a grinding noise in the bottom of the dishwasher, and then the thing just stopped cleaning the dishes. It wasn't pumping any water,
I removed the plasic inner parts, used the torx drivers to remove the internal platic plate that covered the sump. Found the food chopper cover and removed it. It had gotten a piece of plastiic wrapped around it. As it spun it had ground the teeth off the end of the drive on the impellor and the food chopper. I replace both as a set and it works fine. Read more...
Your Price
$29.10
  In Stock
Maytag Dishwasher Cover
★★★★★
★★★★★
1 Review
PartSelect Number PS11755007
Manufacturer Part Number WPW10455271
Fixes these symptoms
Videos!
Your Price
$64.17
  In Stock
Maytag Dishwasher Wash Impeller
★★★★★
★★★★★
5 Reviews
PartSelect Number PS11747701
Manufacturer Part Number WP99002659
This impeller rotates and is used to force water up through to the spray arm.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Timothy from Trevor, WI
Dishwasher would fill properly but when wash cycle would start you could not hear any water spraying.
First I removed the lower spray arm by removing the middle retainer nut. Next remove the 3 screws holding the outer shroud in place. Next remove 6 screws holding the water pump top housing in place. Under this housing you will find the impeller which is retained by a screw. Check the impeller closely for cracks especially near the center hex portion of the impeller. Replace if you have any doubt of it's integrity. Next remove the lower pump housing that has the screen material in the center. What I found was the nylon part that attaches to the shaft of the motor was stripped so the impeller would spin in it's normal direction ( counterclockwise) but under the load of water it would not. So I ordered a new impeller and seal kit with a metal sleeve and chooper blade. Follow the instructions provided in the new kit a reassemble accordingly. Read more...

Related Maytag Dishwasher Parts

Back to Top