Official Magic Chef Dishwasher Parts

Videos!

Dishwasher Rack Track Stop – Part Number: WP8565925

Your Price

$9.62

Magic Chef Dishwasher Rack Track Stop

★★★★★

145 Reviews

PartSelect Number PS11746591

Manufacturer Part Number WP8565925

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack stop may need to be replaced. The replacement part may differ slightly from the broken part, depending on the model. However, the different styles are interchangeable. This product is sold individually and comes in both a white and grey plastic version. Many of our customers found this repair to be very easy and takes less than 30 minutes to complete. Simply snap the old part out and snap the new part into place. You will not require any tools to complete the job. This is an authentic part approved by the manufacturer.

Fixes these symptoms

Door latch failure
Door won’t close
Leaking
See more...

Installation Instructions

Steven from WASHINGTON, DC

Upper rack wheels had begun to break off. Shoddy design and materials.

I carefully followed the video instructions step by step. They were detailed, clear, and pointed out how to avoid installation mistakes. WIthout the video I would have been tempted to just figure it out myself - ("Hey, I'm a handy guy. How hard could it be, right?"). With the video I sailed right through with no dumb errors. The new rack adjuster wheel set is much sturdier than the Whirlpool original. It made sense to get new rack stops at the same time. Thank you, PartSelect. Read more...

Videos!

Dishwasher Heating Element – Part Number: W10518394

Your Price

$46.34

Magic Chef Dishwasher Heating Element

★★★★★

114 Reviews

PartSelect Number PS8260087

Manufacturer Part Number W10518394

This manufacturer-certified heating element is used to create heat during the dry cycle and increase water temperature during portions of the wash cycle when certain options are selected. If your dishes are not drying or the water in the dishwasher is not getting hot you may need to replace the element. This kit includes the heater, two heater fasteners, and is a genuine OEM part. Please remember to disconnect the power before starting the repair. Use a multi-meter to test your heating element for continuity to determine whether this is the part that is causing your symptom. This part does not include any washers. To make your repair, disconnect the wires from the bottom of the element in the back, remove the plastic nuts holding it in place, remove the element, and repeat these steps in reverse order to install your new part. This is an easy repair that requires only a screwdriver, wrench set, and should take less than 30 minutes.

Fixes these symptoms

Leaking
Not cleaning dishes properly
Not draining
See more...

Installation Instructions

Dennis from Sedro Woolley, WA

Heater element broken.

Step 1: Remove the screws in the bottom of the countertop.

Step 2: Remove the screws holding the bottom kickplate.

Step 3: Loosen leveling legs.

Step 4: Pull dishwasher out of hole.

Step 5: Unlplug dishwasher.

Step 6: Disconnect wires from bottom of element in back.

Step 7: Remove plastic nuts holding element in place.

Step 8: Remove element.

Step 9: Reverse Steps 1-7.

Step 10: Drink beer. Read more...

Videos!

Dishwasher Mounting Bracket – Part Number: WP8269145

Your Price

$15.00

Magic Chef Dishwasher Mounting Bracket

★★★★★

14 Reviews

PartSelect Number PS11745496

Manufacturer Part Number WP8269145

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.

Fixes these symptoms

Door latch failure
Door won’t close
Leaking
See more...

Installation Instructions

Judith from Essex, MA

Lost dishwasher brackets

I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief! Read more...

Videos!

Dishwasher Drain Pump – Part Number: WPW10348269

Your Price

$62.60

Magic Chef Dishwasher Drain Pump

★★★★★

65 Reviews

PartSelect Number PS11753379

Manufacturer Part Number WPW10348269

This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.

Fixes these symptoms

Leaking
Noisy
Not cleaning dishes properly
See more...

Installation Instructions

Andrew from Alexandria, VA

dishwasher not draining after wash cycle

Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.

First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done. Read more...

Videos!

Dishwasher INLET VALVE – Part Number: W11175771

Your Price

$54.24

Magic Chef Dishwasher Inlet Valve

★★★★★

38 Reviews

PartSelect Number PS12578165

Manufacturer Part Number W11175771

This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

Fixes these symptoms

Leaking
Noisy
Not cleaning dishes properly
See more...

Installation Instructions

Melissa from AIKEN, SC

Inlet valve wasn't working

Put thread tape on threads. Screwed water hose to part. Pushed hose onto part. Pushed electric clip to part. Screwed part onto washer. Done Read more...

Videos!

Dishwasher Door Gasket with Strike - Black – Part Number: W10542314

Your Price

$59.47

Magic Chef Dishwasher Door Gasket With Strike - Black

★★★★★

67 Reviews

PartSelect Number PS5136129

Manufacturer Part Number W10542314

This dishwasher door gasket and strike kit is an essential component for maintaining a watertight seal around the dishwasher door and ensuring proper latch operation. The gasket prevents water leakage by forming a tight seal between the door and the tub, while the strike works as a mechanical actuator for the door switch and provides tension for a secure seal. Over time, wear and tear may cause tears, gaps, or cuts in the gasket, leading to leaks. This genuine OEM replacement kit is compatible with select models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dishwashers. For proper installation, unplug the dishwasher or turn off the circuit breaker to ensure safety. Refer to the installation guide or video for step-by-step instructions, and wear protective gloves while replacing the gasket and strike.

Fixes these symptoms

Door latch failure
Door won’t close
Leaking
See more...

Installation Instructions

Penny from Manchester, MI

The door gasket stuck to the door a pulled out of place after every use

Worked the new gasket into the groove with a smooth screwdriver and my fingers. No leaks and it stays in place. Parts Select had the right part and I got it fast Read more...

Videos!

Dishwasher Friction Sleeve – Part Number: WP8268961

Your Price

$9.62

Magic Chef Dishwasher Friction Sleeve

★★★★★

37 Reviews

PartSelect Number PS11745488

Manufacturer Part Number WP8268961

This part helps to keep your door quiet when it opens and closes.

Fixes these symptoms

Door latch failure
Door won’t close
Noisy
See more...

Installation Instructions

Arthur from YORKTOWN HTS, NY

Door will fall down after opening

unscrewed dishwasher from cabinet ...,moved out slightly....while door closed ...reached with long nosed pliers door spring pulled forward...and allowing white plastic part that fits through sleeve and fit new sleeve over it...pulled spring attaching white plastic part and pushed unit back to cabinet and replaced screws DONE. Read more...

Videos!

Dishwasher Rack Adjuster – Part Number: WPW10204131

Your Price

$9.62

Magic Chef Dishwasher Rack Adjuster

★★★★★

39 Reviews

PartSelect Number PS11750255

Manufacturer Part Number WPW10204131

This OEM dishrack roller and adjuster is found in your dishwasher. They work together to support and facilitate the smooth movement of your dishrack. The dishrack rollers are small wheels located on the sides of the dishrack and allow it to slide in and out effortlessly. Meanwhile, the dishrack adjuster is used to adjust the height via the selector at the back of this component. Over time, the rollers wear out. You may experience resistance or difficulty when sliding the dishrack in or out. If left unreplaced, your rollers or adjuster may break, causing dishes to tilt, collide, or fall over during the wash cycle. When removing a roller and adjuster from your appliance, you will need to pull out the dishrack partway. Detach the assembly by depressing the tabs on the two end stops before lifting them up. Keep in mind that the roller and adjuster are sold together, but the dishrack itself is sold separately.

Installation Instructions

Randy from Glenview, IL

Replacement of broken Rack Assembly Mount with Wheel

The only piece that may be a little difficult to remove here without a tool is the 'Track Stop'. This piece has a couple of clip-like pieces that need to be depressed in order to remove it. A flathead screw driver will do the trick. Once this piece is out and you have popped the Mount off of the Rack, you simply roll the piece out of the track, roll the new one in and snap the new Mount in place, replacing the Track Stop when you are done. VERY EASY! Read more...

Videos!

Dishwasher High Limit Thermostat – Part Number: WP661566

Your Price

$29.47

Magic Chef Dishwasher High Limit Thermostat

★★★★★

10 Reviews

PartSelect Number PS11743423

Manufacturer Part Number WP661566

This part acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this part will shut down power to the heating element.

Fixes these symptoms

Not cleaning dishes properly
Not drying dishes properly
Will Not Start
See more...

Installation Instructions

PAUL from ESTES PARK, CO

Unit Wouldn't Work. "Clean" Light Blinking

The unit had power, but the controls would not work. The "clean" light was blinking. I first replaced the control unit, no help. I then used the "just ask" and was told the problem was the heating element and/or the hi-temp thermostat. I replaced both those and used the re-set code pushing the "hi-temp/air dry, hi-temp/air dry" buttons. That did it. Easy parts to locate and replace. It took longer pulling the unit out and putting it back than it did to replace the parts. Read more...

Videos!