Hotpoint Refrigerator Dispensers

Find Your Part

Model number locator Need help finding your model number?
  • Search your model number to find:
  • Genuine OEM parts guaranteed to fit
  • Free manuals and guides
  • Repair instructions and videos
Hotpoint Appliance Parts
Shop By Part Type

Popular Hotpoint Refrigerator Dispensers

Videos!
Your Price
$64.74
  In Stock
Hotpoint Refrigerator Dispenser Door Solenoid Assembly
★★★★★
★★★★★
33 Reviews
PartSelect Number PS1483583
Manufacturer Part Number WR62X10055
This part is a possible option when ice door won't open or shut properly or when water is not dispensing.
Fixes these symptoms
  • Door Sweating
  • Door won’t open or close
  • Freezer not defrosting
  • See more...
Installation Instructions
Bill from Cleveland Heights, OH
flap to ice dispenser would not close
The flap to the ice dispenser would not close, which allowed the ice dispenser to frost up, freezing the water dispenser.

This was a simple fix. The solenoid had stopped working, so it would not automatically close the door flap. I read some posts on this site that suggest that you had to remove the trim around the entire dispenser to get at the solenoid. My fridge may be a newer model, but in any event it was much easier than that. Just below the touch pad for choosing water, ice, or crushed ice (above where the ice/water dispenses) there are three very small holes spaced about an inch a part. After unplugging the fridge, I stuck a small philips-head screw driver in each, freeing spring clips. That allowed the touch pad to come off. I then removed four screws to remove a plastic piece covering the chute, giving me access to the flap and solenoid. I just unplugged the solenoid from the circuit board on the back of the touch pad and then removed three screws to remove the old solenoid. I replaced it with the new solenoid and plugged it into the circuit board. The touch pad then snapped back into place.

The hardest part was figuring out how to get at the solenoid. After I found that pushing the clips in those three holes allowed me to remove the touch pad, it could not be any easier. Read more...
Videos!
Your Price
$15.58
  In Stock
Hotpoint Refrigerator Dispenser Door Assembly or Flapper
★★★★★
★★★★★
87 Reviews
PartSelect Number PS964304
Manufacturer Part Number WR17X11653
This “Dispenser Door Assembly” (Door Recess Assembly, Ice Door Assembly, Dispenser Door, Refrigerator Dispenser Ice Chute Door Kit, Dispenser Door Flap, Ice Chute Door, Flapper) keeps the room air from infiltrating the freezer. Once the lever is pressed, the door flap opens and allows the ice to dispense into your container. If your door flapper is broken, it could allow outside air to enter the freezer and alter the inside temperature. You may notice frost buildup surrounding the dispenser area. The door flap can disconnect from the dispenser lever, or the tabs that hold it in place may break. Frequent use may distort the sealing face and cause air leaks and frost buildup. This part mounts in the ice dispenser, and measures approximately 3.25 inches in diameter. It is constructed of plastic and rubber, and comes in white/black. This part is sold individually.
Fixes these symptoms
  • Door Sweating
  • Door won’t open or close
  • Freezer not defrosting
  • See more...
Installation Instructions
ALBERT from RALEIGH, NC
Our Ice Damper was warped, which let warm air into the freezer and caused frost to form. Also, our ice and water dispensers stopped working.
Swapping out the ice dispenser damper door was pretty easy- just used a combination of screwdrivers to remove the dispenser assembly, popped the old damper off, put the new damper on. Replacing the control board was only a bit more complicated- unplugged the fridge, removed the control board metal cover (beware the somewhat sharp edges), unhooked all the cables from the board, used needle-nose pliers to pinch each plastic spacer/fastener as to not damage them while removing the old board, mounted the new board where the old board was, and plugged in all the cables (they were all different enough from each other that I didn't have any trouble figuring out where they were supposed to connect). I now have my fridge plugged into a surge protector- hopefully that will protect this new board I've installed. Thanks a bunch,PartSelect. Read more...
Videos!
Your Price
$13.84
  In Stock
Hotpoint Refrigerator Dispenser Door Recess Crank
★★★★★
★★★★★
1 Review
PartSelect Number PS291908
Manufacturer Part Number WR17X10706
The door recess crank for your refrigerator is located inside the water dispenser assembly. To access this part, you will need to take apart the dispenser assembly. To do this, you will need a putty knife and a Phillips screwdriver. If your dispenser door will not close properly, or ice is not dispensing properly, you may have a damaged door recess crank. This part is made of white plastic and is sold individually.
Fixes these symptoms
  • Door Sweating
  • Door won’t open or close
  • Freezer section too warm
  • See more...
Installation Instructions
James from Malabar, FL
Ice Chute Flapper not closing causing water dripping to floor and ice chute freezing up solid
I followed the video instructions for replacing the Flapper Valve and solenoid that Part Select suggested. It was one of the best DIY Reapair Sites I've used. Thank you Read more...
Your Price
$41.04
  In Stock
Hotpoint Refrigerator Ice Funnel
★★★★★
★★★★★
25 Reviews
PartSelect Number PS652226
Manufacturer Part Number WR17X11267
This paddle, when your glass is pushed against it, activates the dispenser to release the ice through the funnel.
Fixes these symptoms
  • Ice maker won’t dispense ice
  • Not dispensing water
  • See more...
Installation Instructions
James from Malabar, FL
Ice Chute Flapper not closing causing water dripping to floor and ice chute freezing up solid
I followed the video instructions for replacing the Flapper Valve and solenoid that Part Select suggested. It was one of the best DIY Reapair Sites I've used. Thank you Read more...
Your Price
$23.45
  In Stock
Hotpoint Refrigerator FUNNEL ICE DISP
★★★★★
★★★★★
1 Review
PartSelect Number PS1483300
Manufacturer Part Number WR17X12120
Your Price
$13.88
  In Stock
Hotpoint Refrigerator Ice Dispenser Lever
★★★★★
★★★★★
1 Review
PartSelect Number PS1483305
Manufacturer Part Number WR17X12125
The dispenser lever releases ice or water when you press the lever.
Fixes these symptoms
Installation Instructions
David from TOWSON, MD
Water not turning off; spring broken off of dispenser lever.
Replacement of Paddle Ice Disp Bk (#70) with Torsion Spring (#74) ---
Pry off bezel with putty knife. Remove control panel. Disconnect connectors. Unscrew (4x) plastic Housing. IMPORTANT: Funnel Ice Disp (#69) MUST be removed from Housing Shield Disp (#58) in order to rotate new part #70 to remove/install. May be tricky as stuck together with age and gunk. Note flat on axle of switch arm of #70; must rotate fully to remove/install part. Install new part with spring, and reassemble. NOTE: there are (at least) two types of bezels: one with spring tabs on the sides that must be felt and pushed in to remove without breaking, and another (mine) with rigid tabs on all sides that must be gently pried to pop out. Read more...
Your Price
$42.46
  In Stock
Hotpoint Refrigerator Ice Funnel - White
★★★★★
★★★★★
6 Reviews
PartSelect Number PS758841
Manufacturer Part Number WR17X11264
This part is the replacement ice funnel for your refrigerator. It is made of white plastic and is sold individually. The funnel is approximately 7 inches wide and 8 inches long. The ice funnel has a paddle that, when pushed by your glass, activates the dispenser and releases ice or water through the funnel. If your refrigerator is not dispensing water or ice, you may have a damaged ice funnel. This is an authentic OEM part sourced directly from the manufacturer.
Fixes these symptoms
Installation Instructions
DALE from JACKSONVILLE, FL
Door Dispencer Wtr/Ice Ran Continuously.
First I removed the front cover (pried a screwdriver gently under the bottom plastic seal between housing shield and front cover, it came off nice and easy without damage). Removed electrical plugs from electronic board (front cover) so that it did not hang from the wires and get it the way. Then removed four screws holding housing shield on. Removed housing shield, first observing with new parts next to me how it came apart. And then disassembled funnel from shield. Simple but being careful is the key to putting the new unit together as with any plastic parts it's easy to snap if forced. Replaced all parts in reverse order removed. This is a good time to clean all parts for any mold build up that could not be reached otherwise. Parts select personnel were courteous and very helpful. Especially when I almost ordered the wrong color parts. Ask questions if not sure. Read more...
Your Price
$77.13
  In Stock
Hotpoint Refrigerator Funnel Extension - Black
PartSelect Number PS966587
Manufacturer Part Number WR49X10076
Installation Instructions
Chris from Old Hickory, TN
Service Tech Melted the funnel and housing for the ice maker
The trim, funnel and housing were removed. I exchanged the small electrical part to the new housing and reinstalled the housing, funnel and trim. It took longer to get the tool then it took to make the repair. Read more...
Your Price
$15.48
  Special Order
Hotpoint Refrigerator GRILLE RECESS
PartSelect Number PS2323085
Manufacturer Part Number WR17X12324
Your Price
$29.61
  In Stock
Hotpoint Refrigerator Dispenser Assembly Crank
PartSelect Number PS293032
Manufacturer Part Number WR17X3089
Fixes these symptoms
Installation Instructions
Michael from Olney, MD
water dispenser not working
I replaced the water solenoid kit,control board and a broken dispenser assembly crank.My repair went well, parts came on time,I watched an R&R video on youtube provided by PartSelect and finished the job in ten minutes. I am one happy do it yourself-er customer. Read more...

Related Hotpoint Refrigerator Parts

Back to Top