Crosley Range Igniters

Crosley Range Oven Bake Igniter

★★★★★

★★★★★

21 Reviews

The oven burner igniter simply ignites the gas so it can heat the oven burner. The igniter does this by drawing electrical currents through the oven safety valve to open it. If the element shortens out, is no longer glowing, or is only glowing red or orange, replacing the igniter is the solution. You will need a wire splicing tool to do this repair. First, disconnect the wire harness from the igniter by removing the access panel on the rear of the stove. Next, access the front of oven and take out the racks before removing the bottom of the oven. For the rest of the installation instructions refer to the diagram provided by the manufacturer. Remember to unplug your oven from the power source before beginning this project.

Crosley Range Oven Burner Igniter

★★★★★

★★★★★

28 Reviews

This is an oven igniter for various ranges. This part is used to ignite the burner within gas ovens. If your oven is not heating properly this igniter has likely failed and is in need of replacement. To replace this igniter, you will need pliers, a screwdriver, and a wrench. This igniter is an OEM part and does not come with any other accompanying parts or accessories.

Crosley Range Flat Style Oven Igniter Kit

★★★★★

★★★★★

55 Reviews

The flat style oven igniter kit is used in gas ovens and ranges. It is what provides the heat needed to open the gas valve, and it ignites fuel for the burner assembly. This part can be used for both bake and broil elements, and it can replace both short and long igniters. However, it cannot replace round style oven igniters. If your igniter glows for 90 seconds or more without igniting the burner, this means it is too weak to open the valve. The element in your igniter may have shorted it and it might not glow at all, or it might only glow orange or red. It needs to glow white hot; if it cannot get hot enough the gas will not be released from the safety valve and it will be impossible to light the burner in your oven. This kit includes the igniter, ceramic wire nuts, an insulation pad, a metal bracket, a variety of plug ends, and an instruction sheet. The body length is 3 3/4 inches, and the element inside is approximately 1 1/2 inches. This replacement part has an amperage range of 3.3 to 3.6. The element inside this igniter is extremely fragile, do not touch it. Before you start repairing your oven or range, make sure you have unplugged it and shut off the gas supply.

Crosley Range Oven Igniter - Vertical Mount Bake and Broil

★★★★★

★★★★★

46 Reviews

This broil igniter assembly comes with its own metallic mounting bracket and a 7-inch-long dual wire lead with a plastic plug. This part will need to be repaired if your oven element is giving off no heat or very little, or is not heating evenly. You may also notice a smell of gas. The ignitor may still be glowing, but could still have gone bad. You will need a 1/4-inch nut-driver and a 5/16 nut-driver. Open the oven door and pull the door off the hinges to completely remove. Pull out the racks. Using your 1/4-inch nut driver, take out the screws at the bottom rear end of the oven, which will allow you to completely remove the bottom. Unscrew the nuts holding the igniter in place. Remove the igniter with the 5/16 nut driver. You should now have access to remove the old igniter.

Crosley Range Top Burner Igniter

★★★★★

★★★★★

20 Reviews

This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, element does not heat, or gas igniter glows but does not light, replacing the igniter can solve these issues. For this installation, you will need a Phillips screwdriver and needle nose pliers. First place the grate on top of the burner, then lift the burner and disconnect the wires. Next remove the two Phillips screws from the bottom of burner, pull igniter out of the burner and wiggle in the new one. Refer to the installation instructions provided by the manufacturer for more instructions.

Crosley Range Bake Igniter

★★★★★

★★★★★

14 Reviews

This is a bake igniter manufactured for an oven, stove, or range burner. It ignites the gas to light the oven burner to bake your food items. If your oven will not heat properly, your igniter could be faulty and you may need to replace it. You can access your bake igniter by removing the bottom panel and burner shield of your oven. Be sure to disconnect power to your appliance before completing this repair because you will be working closely with wiring harnesses. This part is sold separately and is a genuine replacement part sourced from the original manufacturer.

Crosley Range Surface Burner Spark Igniter

★★★★★

★★★★★

8 Reviews

This part helps your burner ignite and produce flame.

Crosley Range Broiler Igniter

★★★★★

★★★★★

1 Review

This igniter has a short wire harness. The wire length is approximately 6 inches long.

Crosley Range Broil Igniter This part ignites the gas to light the oven burner.

Crosley Range Front Burner Igniter/Orifice Assembly

★★★★★

★★★★★

3 Reviews

This igniter and orifice assembly is a legitimate OEM replacement part for your gas stove, and includes the igniter, orifice assembly, and gas tube. This part may need replacing if the igniter fails or the tube is leaking gas. It is a very easy repair. Remove the grates and burners from the range. Unscrew the existing assemblies and pry off the cooktop. Locate the assembly you are replacing and undo the nut holding it in place. Pull out the igniter wire by hand, and install the new one, replacing the rest of the parts in reverse order.