This lower rack wheel kit includes 8 wheels and 8 axles that allow the lower dishwasher rack to slide in and out smoothly. If your dishwasher door will not close, is noisy when operating, or the dishe...
The Rack Slide End Cap is a white one-inch plastic part which replaces the end cap for your dishwasher rack, preventing your rack from sliding too far. If you find the dish rack is causing the door to...
The dishwasher roller assembly attaches to the upper dishrack. It allows the dishrack to slide out easily. If the upper rack keeps falling off the track in dishwasher, the door will not close, the doo...
The lower dishrack wheel on your dishwasher allows the dishrack to roll in and out effectively. If your lower dishrack wheels are damaged, or the rack does not roll in and out, you may need to replace...
This baffle fits the lower right hand corner of some dishwashers. It is black rubber and has a matching left hand lower corner baffle. It is recommended that you replace and install both left and righ...
The corner tub baffle may also be known as the door baffle and is a part used on your dishwasher. The left and right side baffle on your dishwasher should be installed and replaced at the same time. T...
The silverware basket, used for dishwashers, is in the bottom of the dishrack. The basket is used to hold eating utensils such as spoons, forks, and knives. If the basket is worn out or broken, you sh...
The interlock switch may also be referred to as a belt switch. This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open. This is a part for your dryer. ...
This push on nut is for your dishwasher or refrigerator. As the name suggests, it pushes into place, rather than being screwed in. It is approximately half an inch in diameter and is made of stainless steel.
This dish rack includes the wheels. This dishrack is for dishwashers. Dishrack holds the dishes in place during the dishwashing cycle
$155.69
In Stock
Questions And Answers for GSC720Y01WH
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kevin
July 21, 2023
the upper rack dishes are not getting clean. no water is reaching them. what might be a solution?
For model number GSC720Y01WH
Hello Kevin, thank you for a very interesting question. According to our research, the upper wash arm circulates water to the dishes in the upper rack. If water can not flow properly through the upper wash arm, the dishes in the upper rack will not clean properly. Over time, food particles get trapped in the tiny holes in the wash arm. If your dishes are coming out dirty, the wash arm might be clogged. To unclog the upper wash arm, remove the wash arm and dislodge any debris from the holes. If this does not fix the issue, replace the motor and pump kit, part number PS260801. The motor drives an impeller to force water up through the wash arms. If the motor is defective, the pump impeller is broken, or some part of the pump is clogged, dishes will not clean properly. Please submit a new question if you have any follow-ups!
Hello John, thank you for reaching out to PartSelect. We recommend replacing the drain shaft seal, part number PS263930, to fix the leaking. Good luck with this repair!
There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece the
... Read moren slide the rollers out. Place two new rollers in the rail and put the plastic end piece on. Use the hammer and punch to bend the metal clip back into place. Snap the rails on the rack and set the rack on the guides in the dishwasher. Replace the top guide using the screwdriver, you will have to twist the rails in order get them in between the guides.
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.
Open the tiny plastic package in inserted the wheel onto the "axle". Opened the dishwasher, pulled out the bottom rack and snapped the wheel onto the rack. Done!