Shindaiwa Edger Parts

Your Price

$6.59

Shindaiwa Edger Primer

★★★★★

3 Reviews

PartSelect Number PS11826485

Manufacturer Part Number P005003120

This Primer Bulb is a clear, plastic, individually sold part with an Outer Diameter of 0.720 inches (18.30 mm) and a Height of 0.674 inches (17.12 mm). With Flange: 0.842" (21.40 mm). This part is rated as Easy to install by customers, and attaches to the primer pump assembly. If the part shows signs of breakage, such as cracks appearing due to the bulb drying out, or fatigue, then it must be replaced. Refer to your owners manual/model number to ensure you are choosing the correct part.

Fixes these symptoms

Will Not Start
See more...

Your Price

$4.99

Shindaiwa Edger Primer Pump

PartSelect Number PS8858167

Manufacturer Part Number 12318140630

The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs onto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.

Your Price

$5.36

Shindaiwa Edger Fuel Filter

★★★★★

2 Reviews

PartSelect Number PS11826311

Manufacturer Part Number A369000480

This OEM Fuel Filter is a silver and white, steel/felt, part measuring about 1.25 inches in length and 3/4 inch wide. It can be installed with pliers and is rated as Easy to install by customers. This part attaches inside the fuel tank to clean the fuel of debris, and should be replaced during regular maintenance, check your manual for recommended replacement time. If the filter is leaking or it has a blockage preventing fuel flow, then it should be replaced. If the engine sounds like it is not getting enough fuel, then remove the filter and check it for blockage.

Installation Instructions

Paul from SENECA, SC

Fuel line grommet rotted

This blower is quite old looked on YouTube. Removed grommet with needle nose pliers. Removed tank to install new parts. I had trouble getting return line off carb so planned to reuse it after grommet was in place. Thin was a mistake because the seated grommet compresses the holes. Took unnecessary time to get it through. With my trimmer with all lines in place. Hardest part was to get the grommet to seat even with silicone. Read more...

Your Price

$8.60

Shindaiwa Edger Filter, Fuel

★★★★★

2 Reviews

PartSelect Number PS11826309

Manufacturer Part Number A369000460

The Fuel Filter is a white and silver, individually sold, steel part. It reuires pliers to install and its installation is rated as Easy. The part attaches inside of the fuel tank and is used to clean the fuel of debris. It should be changed regularly. Check your owners manual for the recommended replacement schedule for your engine. If the fuel is leaking or their is a blockage, you will know the part is broken and will likely need to be replaced. To check for small leaks, feel around for dampness and the smell of fuel.

Installation Instructions

Keith from NORWOOD, NJ

Replace clogged fuel filter.

Thru fuel cap, insert copper wire with hook formed on end. Fish around until you grab the fuel line. Pull the fuel line and filter thru the fuel fill neck.
Pull off old filter and replace with new. Push back into fuel tank & be done. Read more...

Intake Insulator Gasket – Part Number: V103001360

Your Price

$5.19

Shindaiwa Edger Intake Insulator Gasket

PartSelect Number PS10053460

Manufacturer Part Number V103001360

Your Price

$6.82

Shindaiwa Edger Fuel Filter

PartSelect Number PS11836543

Manufacturer Part Number A369000440

This OEM Fuel Filter is a white and silver, steel part, sold individually. It requires a pair of pliers to install and is ranked as Easy to repair by our customers. This part attaches inside of the fuel tank, and is used to clean the fuel of debris. This part should be changed regularly as part of good engine maintenance. If the engine sounds like it is not getting enough fuel or is underperforming, remove the filter to heck for a blockage. If there is a blockage or the part is leaking, then it likely needs a replacement.

Your Price

$5.19

Shindaiwa Edger Gasket

PartSelect Number PS9237390

Manufacturer Part Number V107000010

This individually sold fuel gasket is designed for use with handheld lawn and garden equipment and is the seal for the gas cap. This gasket is a genuine OEM part made of a composite material and will eventually become brittle because it interacts with gas and oil, meaning it will need replacing before it becomes debris in the fuel tank. This gasket not only prevents debris from entering the fuel tank, but it also prevents any leaks. To replace, simply unscrew your gas cap and remove the old gasket from the cap, and then replace it with the new.

Gasket-Cylinder Base – Part Number: 10101044332

Your Price

$5.19

Shindaiwa Edger Gasket-Cylinder Base

PartSelect Number PS8819876

Manufacturer Part Number 10101044332

Your Price

$4.99

Shindaiwa Edger Nut 5

PartSelect Number PS9148697

Manufacturer Part Number 90050000005

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have various uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.