Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS9861764
May differ in appearance but functions same as original.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I removed the two screws at the front above the drum opening (with the dryer door open). The top panel then lifts off. I removed the screw at each side that holds the front panel to the side panels, tilted the front panel forward, which disengages the front of the drum from the front drum glide bearing. I then lifted the front panel slightly, unhooking the bottom of the panel from the dryer base, and swung the front panel aside. I removed the existing top drum bearing guide, which was disintegrated, and snapped in the new bearing guide, with the nylon slide strips installed in the bearing guide. Next pulled out the old felt strip, and pressed the new one in place. I then put the bottom of the front panel back into the bottom of the dryer front, and while lifting the drum to asure it fit over the bearing guide, pushed the front panel back to a vertical position to mate with the side panels. I then replaced the side panel screws, replaced the top, and replaced the front top panel screws.
Basically, I followed the same steps a prior person posted.1.Removed the two screws inside the door, on the top part of the opening.2.Lifted up and removed the top.3.Removed two screws holding the front panel in place.4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at the drum bearing without pulling the wires connecting it to the front panel. The wires are not very long, so I had to be careful not to pull on them.5.Carefully pried off the old drum bearing, using just my hands. It was fairly tight, and popped out just as I started to worry if I was putting too much pressure on it.6.Checked to see how the old felt was installed, then I pulled out the old felt.7.Inserted the new felt, being careful to insert one end into a slot the same way the original was installed.8.Inserted the new slides into the new drum bearing. The gray slides went in at the eleven and one o'clock positions, the white slides went in at ten and two o'clock. 9.Removed a surplus plastic piece from the new drum bearing (where the light comes through).10.Inserted the new drum bearing, putting the bottom tabs in first, then pivoting it into place. I squeezed it into place to make sure it was tight.11.Lifted up the drum and put the front panel back on.12.Screwed the front panel back on, using the two screws.13.Carefully put the top back on.14.Screwed in the two screws inside the front door to fasten down the top.That was it! I started up the dryer and it worked fine. No more squeaking. About the only thing odd about the repair is why PartSelect sells each slide separately (i.e., I had to order 2 white slides and 2 gray slides). I can't imagine replacing just one, so why not package them in pairs, or maybe even all four in one package.At any rate, the repair was easy, and a lot cheaper than having someone come out to fix it.
(1) open dryer door (2) remove screws holding door on and put door aside. Probably doesn't have to be done but I think its easier and safer so you don't accidently bend the hinges. (3) remove 2 screws holding top onto front. of dryer located in recess that door sits in (3) pull up on top and remove (from slots by the control panel) (4) remove final 2 screws holding front onto frame of dryer. You can disconnect the connectors from the front panel back to the dryer to make the job easier or work with it without disconnecting. I'd take your time and clean any lint dust, etc. (5) the Drum Bearing removes fairly easy as it is just snapped into 2 slots. insert slids into slots.... make sure you order all 4. Mine were all beat!. (6) replace with new Drum Bearing. (7) I did the lower felt seal as well. Pay attention to how you took the old one off and replace the same way. Remember it stretches to fit into the slots. Put all back together. Remember to front panel has to sit correctly into bottom slots before you screw the top screws back in. All in all.... a simple project, and no more noise!!!!! Great to have websites like this. Easy ordering, quick shipping, great diagrams.
1. Removed top cap on lid by removing the 3 - phillips screws.2. removed front digital display panel from PC board.3. removed bolts with nut-driver on the top of the front panel, removed bottom screws with #2 square bit.4. removed "snap-in" plastic top bearing ( paying attention to where wiring is routed within this frame.5. cleaned all areas of plastic and felt debris, installed new bearing, felt, and glides.6. Re-installed all wiring and panels.*** make sure to order all of the glides, there should be a total of 4 for the top assembly.
Dear PartSelect.com,My repair went off without a hitch.2 screws removed to remove top.4 screws removed from inside to remove front panel w/ door.4 screws removed from top of control panel, loosed and popped top right off.Flathead screwdriver to pop off old plastic panel.Removed old wire chase (plastic, approx 3” long).Removed built-up lint, wiped down area for new duct.Snapped new duct on.Dryer works like new!!Took about 35 minutes, most of time spent cleaning up inside of dryer from lint due to broken duct.One problem was that salesperson sold me on a new felt strip to go with new duct. That felt comes already installed on the new duct so I did not need it. Cost me a few extra dollars I did not need to spend.Other than that, easy ordering, fast shipment, and parts are as close to original as possible.Thanks for all your help!
Repair was easy, following the disassembly instructions from the video on your site. What I did not know is that it takes 2 pieces of plastic slides from each kind to replace (makes a total of 4). I was lucky in that one of the white ones was still okay and that I accidentally ordered a second one from the greenish kind, so I was set. This was also a great opportunity to clean out the dryer which must have been a bucket full of lint. So far no more complaints. Given that this problem seems to reappear once in a while I'll order a new set soon.
I removed the two screws that hold the front panel to the top panel. I removed two more screws that hold the front panel to the side panels. I separated the front panel from the side panels and removed the drum. I could see on the front panel the drum slides were badly worn. One was gone. The new parts installed easily using no tools at all. Everything snaps in place. The new foam gaskets press and stick to seal the duct work. The felt strip pressed into place. I replace all the panels in reverse order and plug it in. It operates fine, but the motor is making the noise. I will look into replacing the motor next.
5 minutes! loosened 4 screws pulled front off replaced bearing, felt, and slides. put everything back together, tightened screws. Worked like a NEW ONE!!!!
Easy repair. Removed top of dryer and removed two screws to front panel and door assembly. Old front air duct assembly was worn and broken, so it literally fell off the panel. I cleaned the front panel and door assembly of all the lint and dirt, and snapped the new parts into place. The new parts came with the gasket and felt drum seal already installed, to all that had to be done was to snap it into place. Installing the drum slides was a breeze. I simply had to slide one end in the slot, position the hole over the pin, and slide the other end in. I put everything back together, and ran a full cycle for test. Dryer works like new, and run quiet.
We removed two screws to remove the top and two screws to remove the front. The dryer drum slides were easy to replace and the felt fit into a track. It was so easy and now my dryer is quiet again, no more rubbing/squeaking. I can't believe that was all we had to do, and for $60.00!!! I'll be back for future parts if needed. Thanks.
To quiet the noise temporarly I would spray silicone into the dryer drum groove on the front inside panel.Got tired of this and removed the top of the dryer by removing two screws under the front bottom of the dryer top. Remove two screws, one on each side of front panel(screws are on the inside). Lift the front panel straight up and swing to the side. Keep the wires connected to the panel. There is plenty of room to move panel about. Note: I replaced the drum bearing thinking it was a one piece unit with the teflon rub strips. All I had to do is order the teflon rub strips and I would have saved 24 dollars. Reverse the disassembly process to assemble.
A quick look inside verified that the drum slides were worn through but I also found that the plastic drum bearing that holds the slides was cracked in a couple different places. Ordered a new drum bearing, new slides, and decided to replace the felt seal as well since it looked pretty ratty. Parts arrived quickly after ordering and installation literally took 15-20 minutes. Purrs like a baby now. Steps: Unplug dryer. remove two screws which hold top of dryer to front. Remove two screws which hold front (door) to rest of unit. No need to disconnect wiring to front door, just make sure not to pull the wires out! Install new parts. Put it back together in reverse order.
Took apart by removing the top and front panel. Found drum rubbing due to worn glides and felt.
Remove front by removing two screws at top of door opening. Remove front of dryer carefully becsuse of electrical connections for door switch. Drum sliders simply silde in slots at top. (4 are required for total replacement) Door seal simply fits in the groove and locks over end tab. NOTE Do not run dryer any more than absolutelty nessary without lower seal in place.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.