8768445-1-S-GE-WH23X10030-Drain Pump and Motor Assembly
8768445-1-S-GE-WH23X10030-Drain Pump and Motor Assembly 8768445-2-S-GE-WH23X10030-Drain Pump and Motor Assembly 8768445-3-S-GE-WH23X10030-Drain Pump and Motor Assembly http://www.partselect.com/Schematics/GE/GE_Thumb/00110803i04.gif

Drain Pump and Motor Assembly

PartSelect Number PS8768445

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Will not drain.
  • Leaking.
  • Pumps but will not spin.
  • Noisy.
  • Compare At

    $51.88
  • You Save

    $8.65
  • Your Price

    $43.23
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 53 reviews What's this?
 

6 of 8 people found this instruction helpful

Parts Used

  • Drain Pump and Motor Assembly

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsPliers, Socket set

Customerjayme from drummonds, TN

My washer would not drain the water out.

IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

  • Drain Pump and Motor Assembly

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench (Adjustable)

CustomerJames from Strafford, NH

Water would not drain from tub.

First I pulled off the front panel using a flat blade screwdriver to get it started. Then I could watch what happening as I tried starting the washer. When I put the dial to the Rinse Cycle and pulled the dial to start the washer, it would start to run for about 5 seconds and then stop. I tried this several times and the same thing happened. I noticed the water pump located in the front lower right hand corner was not running. It would only hum. I drained the tub by holding the wash machine drain hose into a bucket. If I held the hose down toward the floor, the water would flow freely out of the hose and into my bucket. As the bucket filled up I just raised the hose, emptied the bucket and repeated the process until the tub was empty. Sure saved time over trying to empty the tub by bailing the water out with a can. After the tub was drained I removed the two hoses from the pump and then the two mounting bolts and the pump was out. I bench checked the pump with an electric cord and it stilled just hummed. I knew for sure then the pump was bad.

I then ordered a new pump from PartsSelect.com. I entered my wash machine model number and PartsSelect gave me a picture of the replacement pump. I was a little worried that it did not look the same as my old pump but I ordered it any how. The night I got the pump I installed it in about 30 minutes. No problems, it just worked like a charm. Thank you PartsSelect.com I will definitely use you for all my appliance repairs in the future. I know there will be more.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Drain Pump and Motor Assembly

Level of DifficultyReally Easy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Wrench set

CustomerRoberto from Nokesville, VA

Some leak

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsPliers, Socket set

CustomerRichard from Garden City, NY

Washer had heavy wet clothes left after spin cycle

The trick is to pull the front cover off by using a putty knife .slide it under the cover at both front corners.it will click on each corner.then pull front cover off .lift off the bottom catch hooks.look for the pump on the bottom right side.unplug the wite connector .take 2-5/16 bolts out holding the bracket.then grab a pliers .squeeze the hose clamps and pull the 2 hoses off.assemble new pump.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 18 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Wrench set

Customerelie from Santa barbara, CA

1)pump leak damage,2) water over fill and leak water out the top

First I disconnect the power and then I pull the front cover and replace the water pump, drain hose, and the inlet hose this was fixed and straight easy job.My second problem was the overfill problem witch I took the knobs cover and I replace the water level switch.This job was also easy but did not fix my problem.

Help other customers find the most helpful instructions.

Were these instructions helpful?