Quick Question!

Have you ever purchased from PartSelect.com before?

7784017-1-S-Frigidaire-242252603-Water Inlet Valve
7784017-1-S-Frigidaire-242252603-Water Inlet Valve 7784017-2-S-Frigidaire-242252603-Water Inlet Valve 7784017-3-S-Frigidaire-242252603-Water Inlet Valve http://www.partselect.com/Schematics/Frigidaire/859UVGY0.gif

Water Inlet Valve

PartSelect Number PS7784017

When energized, this part releases water from the supply line into the ice mold.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Leaking.
  • Ice maker won’t dispense ice.

Compare At

$25.75

You Save

$4.29

Your Price

$21.46
Order within the next 24 mins and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 8 reviews What's this?
1-8 of 8
 

38 of 63 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: Orville from Garland, TX

Was not filling the ice tray full.

I had put in a new ice maker and it still had the problem, (I needed the Ice maker anyway) I installed the vale and while I was at it I put a five year filter on the water line that went from the value to the Ice maker, it took less than one hours, the ice is making like it did when it was new, I could not be more please at theis time. Thanks for your Interest. God bless.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

24 of 35 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set, Wrench (Adjustable)
Customer: Jerald from Phoenix, AZ

Ice maker water would constantly drip. Forming a huge block of ice.

Pulled refrig away from wall, shut off water supply. Removed two screws holding the old water value on the back of the refrig. Removed the two water lines from the value. Hooked water lines up to the new value and bolted the two screws and the new value on. Turned on water and pushed refrig back into position. Simple and it worked. No more huge blocks of ice. I have Cubes!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

18 of 26 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: BARBARA from DIAMOND, IL

Water was not being sent up to ice maker

I removed a couple of screws from the old part, and inserted the new part. Replaced the screws and I was done. No problem. I'm an almost 60 year old woman, and fixed this myself. It was so easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

10 of 24 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers
Customer: timothy from georgetown, TN

Water valve was leaking water and not making ice

I unplugged the fridge and unscrewed the back cover,unscrewwd the two screws holding the water valve in place and the water line to the ice maker and the electrical connection and install the new water valve,then buttoned everything back up and plugged the fridge back in and it is working great,making ice as normal.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 10 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Fred from Las Vegas, NV

Ice maker stopped working

Took off old part and installed new part

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers
Customer: Patrick from RICHWOOD, TX

The fan had stopped spinning. According to the internet it should spin freely if I use my hand, but it wouldn't.

After pulling the fridge away from the wall and opening the paper backing on the bottom, I could see the motor. It's affixed to 3 metal ribs by 3 small screw/nuts. There is also a 12" wiring harness that led to a simple disconnect. Removing the disconnect and the 3 nuts was easy. However, there was no room to remove the motor with the fan attached. Between frame parts, the drip pan below, the ribs, and small, delicate copper tubing that can't get bent, it wouldn't fit thru any openings. So we rotated the motor inside the framework until the blade faced out, then reached in with a pair of needle nose pliers to remove the washer. Removing the washer is easy, it's just difficult to reach. With the washer off the fan was out of the way and very carefully (it was tight) the motor came out. Reverse was the same issue. Motor tight going in, not a lot of room to maneuver fan onto motor, and needed needle nose to tighten washer again. Make sure you tighten the washer before you install the motor on the prongs. Otherwise you need to remove it from the ribs, twist it to face you, then reinstall it on the prongs. Also, I felt I was stripping the nuts into the new motor. Turns out the holes in the motor aren't tapped. i realized the nuts are self tapping once I looked at them. I'm a big time DIYer and this wasn't bad at all. If your motor/fan assembly comes out whole, it's even easier.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 8 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Louis from Damascus, PA

Warter valvr cracked

It was real easy but I still have problem making ice cubs
Fell problem is in the ice maker went it dose make cubs they don,t dump

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 7 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Pliers
Customer: Leah from Tecumseh, OK

After installing new ice maker water was not running into the ice maker.

Shut off water supply under the sink. Removed old valve and installed new valve. Turned water back on and within a couple hours the first batch of ice made.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-8 of 8