This part is between the front and rear outer tubs.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Frigidaire, Kenmore, Gibson, Crosley.
Part# 134146100 replaces these:
AP3212518, 936915, 131275900
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Steve G - March 9, 2018
Verified Purchase
OEM Part
Part appeared to be exactly as OEM part that was factory installed. I used several small dabs of sealer to insure o-ring stayed in position,and assembled immediately. Was part of tub bearings and seal replacement. Washer is performing as new. PartsSelect is punctual and accurate as they have been in the past. Competitively priced compared to other on-line parts retailers. Had part in-hand within 3 days of ordering.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 1.8 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Spider was corroded and broke from being weakened by the corrosion
Removed the entire front cover of the washing machine and dicoonected the springs that support the tub. Left the tub down and disconnected the struts and unhooked all the wiring and pulled complete tub out of machine. Removed all the bolts around the tub shell and split the tub shell. Remover the motor from the sheel to make it lighter to
... Read more work on, removed the pulley on the drum shaft and pulled the drum out of the shell. Found that the cast alluminum spider was weakened by corrosion and this caused the spider to break. The spider itself should be able to be purchased seperately because the stainless steel drum was okay and could have been reused. The biggets problem I had was getting the tub back in the washing machine and getting it suspended by the springs again. I used a 6 x6 block and a 2 x 6 board to lift the tub up in the air to get the tub springs hooked back up. This took 2 people to accomplished. After the tub was suspended on the springs the rest was easy.
Stainless tub in front loader broke 2 out of 3 spider arms
Removed entire tub assembly, replaced bearings and seal in rear outer tub assembly, had spider arms welded by aluminum welder. alot of work ,saved 150.00 on parts by replacing bearings, savings untold hundreds by doing it myself instead of replare man.. BIG JOB. But just plug away and it goes rather smoothly.
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Anthony
November 26, 2017
I have water leaking when doing the wash and water is leaking from behind the front and rear tub. Is that the o ring/gasket or can it be coming from the door gasket. Please give me an idea. I really appreciate it.
For model number 417.44102300
Hi Anthony, Thank you for the question. It sounds more like the O-Ring/Gasket if it is coming from the front and rear of the tub. Only way to know for sure would be to take the drum apart to check the gasket. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Jerry
January 2, 2019
The washing machine makes a grinding noise when it is spinning and the drum (basket) shakes when you move it back and forth. It sounds like a bearing or something is bad. What would your guess be?
For model number FTF530FS0
Hello Jerry, Thank you for the question. This does sound like a Bearing issue. The bearing is only sold as part of the Rear Outer Tub Assembly, PartSelect Number PS418071. The seal and bearing are included and are not sold separately. Thank you for your inquiry, good luck with this repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.