Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS460194
This part helps to keep the dryer running as quietly as possible.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
Front upper felt glide pad with 3 nylon glides - includes adhesive.
Used for installing felt and rubber seals on dryers.
I followed the recommendation from William, from Ardmore, OK and Elvis, from Miami, FL for the repairs. Elvis had detailed instructions as well as William, so I just combined the two and I was able to repair my dryer in three hours time. My sincere thanks to partselect web site in posting the repairs on line and for everyones input. I will be back to use the web site again to troubleshoot my other appliances and order parts (great price, fast service for parts) and I will highly recommend this site to my friends.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Took apart the dryer, definitely a two person job. Cleaned up a bag full of lint that collected in the dryer (can't believe it didn't start a fire!), removed the old glides and seals, sandpapered off the old adhesive, applied fresh adhesive, attached the glide and seals, waited for the adhesive to dry, reassembled the dryer. Now it's working like a charm!
Follwed all the other comments real easy
disconnected power unlocked both top sides ,lift top back and take top 2 screws out, then unhooked wiring,then remove whole front away from drum.scrap off all the remaining pieces, then glue and wait till tacky, then apply front lower basket seal and top drum glide seal,replace the front ,hook wires back to proper place , put the two top screw back on!!! happy drying!!!
This was a simple repair. Before I ordered the parts I had read several of the "repair stories" on this site, plus my neighbor explained to me the process. So I had a good idea of what I was getting into.I am not real sure how long it took because I was watching a football game while I was making the repair, but I would guess if I did it straight through it would be about 1 hr.Replacing the Drum Glide and Lower Basket Seal1) Pulled dryer out from the wall2) Unplugged Dryer3) Pop the top off the dryer. Insert a screw driver in the crack right at the corners to pry the top off.4) My dryer had a quick connector for all the wiring (which I found half way through the repair) that allowed me to disconnect all the wires leading to the door. If you can find that disconnect that so you can easily remove the door & front panel.5) Removed two screws holding the front panel on.6) Remove the front panel. Once the 2 screws are removed the only thing holding my front panel on were a couple of clips.7) Removed the Drum Glide (top) & Lower Basket Seal (bottom) around the door frame in the front panel. This is the worst part because you have to scrape a lot of the glue and it takes a little while to do this.8) Glue the Drum Glide. I used some spring clamps to hold it in place. Glue did come with the Drum Glide (but not the Lower Basket Seal)9) Glue the Lower Basket Seal. Since I only had 4 spring clamps I waited until the Drum Glide was secure. So if you have several of these clamps that would be best.** if not replacing the belt skip that section.Replacing Dryer Drum BeltI took a lot of the people's advise and replaced the belt while I had the dryer apart. But if you are only replacing the belt perform steps 1 - 6 above first.1) Remove the access panel on the back of the dryer. Mine had for screws.2) Remove the belt. There is a spring loaded pulley that you just move to one side so the belt will loosen up enough to remove.3) Place the new belt on. I started in the front and moved the belt over the drum to the back. Then moved to the back of the dryer and through the access panel placed the belt over the pulleys.Thats pretty much it. I barely got dirty. Oh, while I was in there I cleaned as much lint as I could. That was the dirty part. Now all you have to do is put it back together.1) Reconnect the front panel, and wire harness.2) Plug it back in.If you are wondering why I didn't replace the bearing, I didn't have any grease and the part fit but didn't look exactly like the current one. And the current one looked ok. Since this was my first attempt at fixing a dryer; I decided not to press my luck.
Removed the door and replace the upper glide and the lower seal. The repair was easy.
Looking from the front at the top cover I lifted the cover with my fingers and inserted a screw driver about one or two inches from each edge.The top pops loose and lifts up like the hood of a car.Inside the dryer on either side behind the front panel there is one screw on each side. Remove the screws and lift the entire panel and door. Then swing the assembly out like a door with a hinge on the right. It won't come off due to the wiring harness.Make sure you study the upper drum glide before removing it. Remove the upper drum glide using Acetone, this is easy but a little messy. Apply glue, I applied to the drum but if I did it again I would apply it to the glide and clamp it to the drum in three or four places.This is an income property and my tenants weren't happy so I didn't wait for the other parts. I don't know now if I really needed them. I will replace them anyway.I realize they make these things easy to repair. It makes the $200+ they charge that much more profitable.I also vacuumed and cleaned inside.This is pretty easy and does not require much skill.Position the panel on the dryer. There are two clips that need to lined up on the bottom and fit the drum back on. Then snap the top cover in and test the dryer.Remove the top replace the front panel screws and snap the top back in.I wish I could post pictures there really isn't much to it.For property owners I would recommend learning how to do this prior to getting a call.Create a kit of parts that will wear or break. $100 will save you the hassle of ordering under pressure and get you up and running that much faster.
OK, this is a follow-on repair story.. I *did not* order the lower basket seal when I ordered the upper basket seal... shame!!! BUT, I am now exceptionally quick at removing the front panel - less than 20 seconds!!!For those who are considering doing this repair, there are more detailed explanations below - my only tip to help do this "quickly" would be to get some automotive brake cleaner to dissolve the old adhesive .. it is AMAZINGLY effective.. The best part is, don't worry about completely removing the old felt when you are tearing it off.. If some is still stuck to the door, it will actually hold some of the brake cleaner in contact with the old adhesive, which accelerates dissolving of the adhesive. Scrape it all off with a plastic scraper, and wipe it down a few times - surface is prepped & ready for the new adhesive + basket seal.. Use spring loaded clamps to hold the seal in place as you install it also.
Taking apart the dryer was easy. Pop the top, take out two screws, separate the front panel from the drum. Removed the old felt seals but much remained. Used a wire wheel on my drill to clean off felt and old glue (most difficult part). Applied new glue,used a band clamp, one hour later I reassembled the dryer; works fine. No more burn marks on clothes!
First, I read the other posts and got a good idea as to how to do it. I needed to replace the upper felt and guides but decided to go ahead and replace the lower felt and the bearing holder as well. If I had been thinking I would have replaced the belt at the same time but, oh well.Disconnect the electric plug from the wall. Pop the top using a medium sized flat head screwdriver.Disconnect the wiring harness at right front of the unit. Remove the two screws near the top of the front panel and squeez the retaining clips. You may need a pair of pliers for this but be gentle.Pull straight up on the front panel to remove it.To get to the bearing holder, remove the drum by first removing the access panel located at the rear of the dryer and removing the belt from the springloaded plastic pulley. With no tension on the belt simply pull up on the drum while also pulling slightly forward. The drum will pop right out but you will have to apply some pressure. There is no need to remove the three screws at the back of the drum on the inside. Once the drum is out, remove the two screws holding the bearing holder and remove the assembly being careful not to lose the single ball bearing at the rear of the assembly. Pay attention as to how the assembly goes together.Scrape off the old felt and glue. Like everyone else, I used a chisle and some GOOP. The old felt came right off with little effort and the GOOP cleaned off the old glue with not too much effort.Apply the glue that comes with the felt glides according to the instructions on the tube. There's plenty to do both upper and lower felt in that tube. I used some spring clamps to firmly set the upper felt. The glue sets in just a few minutes. The lower felt has a bevelled edge that goes toward the door and fits into a groove on the panel. Once the glue is set you you are ready to put it back together. Like everyone else, I took the time to vacuum out the interior of the dryer and collect the coins and buttons that had accumulated. I found it very easy to reinstall the bearing holder assembly by myself by working from the side of the dryer. I put a dab of grease on the single ball bearing to hold it in place while I reinstalled the assembly. Put some grease in the bearing holder and reinstall the drum, then the front panel and belt. Put the belt back on the tensioner and take care of the couple of lose end and you're done.This is a "no big deal" repair that looks worse than it is. It took me about 2.5 hours to complete and I was taking my time and just enjoying the fact that I was doing it myself.
Found instructions, correct except for 2 screws at the bottom of the kickplate, which turned out to be 2 philips head screws at top holding control panel to case. Would advise using gloves when holding drum, because front and rear lips are very sharp. This is the second time drum guide and lower basket seal where replaced. First time was in 2006. Saved a bunch of money by doing repair myself. If I had to pay for service call and parts replacement I probability considered replacing unit rather than repair.
removed old seal and drum glide. sanded off old glue. replaced with new parts, cleaned out the whole bottom of the dryer, runs good as new.
Partselect provided me with what to look for with my symptoms and excellent delivery time.
This is the second time that I have replaced these parts on this unit. The top pops up and then removing two screws holding the front panel on,just pop it off - don't forget to unplug the connector on the top right. Scrape the old drum glide and basket seal off of the front panel making sure you get as much as possible off, clean the surface and re-glue both pieces back onto the panel. The glue set up pretty fast so don't linger. Re-assemble and you're good to go. The hardest part is getting the old glide and seal off - that took about 1 hour of scraping. Make sure you get it clean.
We followed Randy from Anchorage, AK's notes pretty much. Took off the top and front panels. Changed the drum glide and lower seal without any problems. Changing the belt proved more difficult. If it's not broke, I wouldn't change it. If you do, DEFINITELY pay attention to how it is looped around the pulleys before disconnecting it (I would take a photo). Definitely open the back of the dryer to do the belt - otherwise the pulley falls before you see how it is connected
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.