Models > 41780042990

41780042990 Kenmore Dryer - Overview

Get Parts and Repair Help for 41780042990

If you know the dryer repair part you need, you can browse the list of all parts on the 41780042990, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for 41780042990 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$21.93

Rear Drum Bearing Kit

This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant and installation screws.

$3.17

Drum Support Bearing

$70.84

Heating Element Assembly

This dryer heating and housing assembly has terminals at four o'clock. This E-line assembly comes with a felt strip and insulators already attached.

$23.51

Upper Drum Glide

Front upper felt glide pad with 3 nylon glides - includes adhesive.

$8.21

Thermal Limiter - Limit 220

This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 ...

$22.80

Front Lower Drum Seal

This part helps to keep the dryer running as quietly as possible.

$18.96

Turn - Type Start Switch

This part is used to start the dryer once you have selected a setting on the timer.

$24.23

Door Catch

$47.18

High Limit Thermostat

This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when th...

$8.29

Bearing Bracket

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loud Squeaking

  • Customer: Frank from Boyertown PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 226 of 234 people found this instruction helpful
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Acc... read more

Drum glide wore down and caused close to get stuck between drum and front panel.

  • Customer: William from Boise ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 159 of 224 people found this instruction helpful
Unpluged dryer. Removed the top of dryer by pushing in a retaining clip on both sides of the front lip with a screw driver. Remove the two screws on both sides of front panel. These screws are square head or phillips #2. Unplugged the wiring harness to front panel (make sure power has been disconnected). Support drum and lean front panel away from dryer ... read more

short circuit with a brasier metal support

  • Customer: Juan Carlos from Weston FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 118 of 141 people found this instruction helpful
Disconect the dryer from the main power source.

1) Remove the two screws from the rear / upper panel (below the control panel).

2) Snap the front side using a flat head screw driver.

3) On the inside front, remove two screws (one on each side) from the upper side and snap the door assembly off.

4) Remove the rear m... read more