Quick Question!

Have you ever purchased from PartSelect.com before?

418726-1-S-Frigidaire-131775600         -Blower Housing with Blower Wheel
418726-1-S-Frigidaire-131775600         -Blower Housing with Blower Wheel 418726-2-S-Frigidaire-131775600         -Blower Housing with Blower Wheel 418726-3-S-Frigidaire-131775600         -Blower Housing with Blower Wheel http://www.partselect.com/Schematics/Frigidaire/2KPITDF4.gif

Blower Housing with Blower Wheel

Compare At

$93.78

You Save

$15.63

Your Price

$78.15
Order within the next 4 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS418726
Manufacturer Part Number 131775600
Manufactured by Frigidaire

***Please Note: This part is a substituted part by the manufacturer. It may appear different, but should still work with your appliance.

This part works with the following brands: Frigidaire, Kenmore, Westinghouse, Gibson, Crosley, Electrolux.

This part works with the following products: Dryer.

This part fixes the following symptoms:

  • Noisy.
  • Takes too long to dry.
  • Will Not Start.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.6 / 5.0, 4 reviews What's this?
1-4 of 4
 

60 of 82 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Customer: Gerald from Cumming, GA

Had 2-seperate problems; 1st was a high pitch squeel, 2nd was the cover overheating

The high pitch squeel was the result of a failing drum bearing. It was particularly evident when first turning on the dryer, but became softer as the dryer heated up. In order to replace the drum bearing, I removed the top panel and front door panel.

The top panel was easily taken off by removing 2-screws from the back edge of the panel, and sliding it back to release it from the front panel seam.

The front panel is more involved, but still relatively easy for your average "do-it-yourselfer". I removed the front door panel by first removing the control panel (4-screws; 2 on top and 2 from the back of the panel). I removed 2 cable assemblies from the control panel via connecters (different sizes so didn't need to mark) and 2-wires attached to the large control panel mode selector (I marked these 2-wires). I set aside the control panel. I removed the front door panel by taking off 6-screws (2 on top, 2 on the bottom, and the remaining 2 on the inside of the panel on either side of the drum). After removing these 6-screws, I carefully pulled the front door panel away from the front of the dryer, carefully releasing 4-alignment latches (2 on either side). The front door panel was still electrically attached to the machine so I had to disconnect a couple more wires. I carefully disconnected 2-wires from the door light assembly and 3 more wires from the door switch (I marked the 3-wires on the door switch). I set aside the front door panel.

From the back of the dryer, I removed the small motor access panel on the bottom left corner. This panel also provides access to the drum belt. I released the drum belt from the motor drive wheel by releasing spring tension at the tensioner. The belt can easily be disconnected from the motor drive wheel and tensioner assemblies.

Removal of the drum was now possible. With the front door panel removed, the front of the drum is maintained in place via a small plastic stop on the top crossmember. I removed this stop prior to removing the drum. With one hand, carefully grabbing the belt that is was loosely draped across the back of the drum, and the other hand holding the front lip of the drum, I provided a quick and forceful upward motion to the back of the drum in order to dislodge the drum shaft from the bearing housing assembly. Once this was accomplished, I simple pulled the drum out of the dryer housing via the front of the machine.

The drum bearing repair kit ordered came with the replacement ball bearing, bearing housing, drum shaft, high-temperature grease, and attaching hardware.

I replaced the drum shaft on the drum via the 4-screws accessed on the drum rear panel.

I removed the old bearing/bearing housing via the 2-screws holding it in place. I wasn't too concerned about loosing the small ball bearing as the kit provided me a new one. I generously applied some high-temperature grease to coat the interior lining of the new bearing housing. I also placed a dab on the back seat where the new ball bearing sits. This helped hold the bearing in place while reattaching it. I reinstalled the bearing housing to finish replacing the repair parts.

Reassembly of the drum is in the reverse order. I paid particular attention to making sure the new drum shaft properly seated with the new drum bearing housing.

After reinstalling the drum and while the front door panel was still off the dryer, it was easy to inspect the blower housing. I found the squirrel cage had broken loose from the molded nut that attaches it to the motor shaft. That would explain the heat problem; the heat was not being exhausted through the duct.

THE SQUIRREL CAGE IS REVERSE THREADED. I was unable to remove the nut from the motor shaft as the design encompasses a metal bushing molded into a plastic nut shaped form. The plastic would not hold up to the force I was applying trying to loosen the squirrel cage. So I ended up removing the entire motor and blower housing assembly from the base

Help other customers find the most helpful instructions.

Were these instructions helpful?   

19 of 43 people found this instruction helpful

Parts Used:
  • Blower Housing with Blower Wheel
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers, Wrench (Adjustable)
Customer: jena from loganville, GA

Blower wheel was raddling

The blower wheel was a bit difficult, but manigable to do yourself.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

13 of 30 people found this instruction helpful

Parts Used:
  • Blower Housing with Blower Wheel
Level of Difficulty: Easy
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers
Customer: Patrick from Littleton, CO

Motor locked

I determined the problem was the fan wheel and housing. I located the part on partsselect.com, Ordered it and installed the afternoon I got it in the mail. Perfect fit.

I have used partsselect before, always had great luck, great prices, always have the exact part.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers, Socket set
Customer: David from PORT CLINTON, OH

Vibration and low pitched grinding noise developed as dryer heated up.

**I'd already installed a new rear drum bearing assembly (very simple) and the issue continued. Further testing (running unit with the drum removed) indicated the blower assembly and/or motor was the source as the issue only occurred when the unit was under load. I ordered both parts as there was simply no way the original blower assembly was coming off the original motor.** Disconnected Power. Removed Top and Front of Dryer. Removed Drum. Disconnected Wiring Harness at Motor. Disconnected Blower Housing Temperature Sensor. Pried Open Clip Holding Motor to Mounting Bracket. Removed All Other Mounting Hardware. Removed Original Motor and Blower Assembly. Mated New Blower Housing to New Motor. Mated Assembly to Mounting Bracket. Reinstalled Clip Holding Motor to Mounting Bracket. Reconnected Wiring Harness at Motor. Reconnected Temperature Sensor to Blower Housing. Installed All Other Mounting Hardware. Reconnected Power. Checked Assembly Alignment. No Issues Noted. Disconnected Power. Reinstalled Drum and Front of Dryer. Reconnected Power. Checked Assembly Alignment While Under Load. No Issues Noted. Reinstalled Top of Dryer. Issue is Resolved. ** Thoroughly cleaned entire unit including under the baffle located at the rear of the drum. Amazing amount of baked on lint located there. Checked heating element (no issues) and cleaned lint trap assembly in door of unit. Another area with an amazing amount of baked on lint. Total for all parts needed was $236.91. Total time needed was about 3 hours. Parts arrived within one day of order. Unit operates 'as-new'.**

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-4 of 4

Model Cross Reference

This part works with the following models:

PartSelect Number: PS418726
Manufacturer Part Number: 131775600
Brand Model Number Description
Kenmore41764182300Dryer
Kenmore41774182300Dryer
Kenmore41774182301Dryer
Kenmore41780412700Dryer
Kenmore41781042000Dryer
Kenmore41781142000Dryer
Kenmore41781142001Dryer
Kenmore41782042101Dryer
Kenmore41782042102Dryer
Kenmore41782052101Dryer
Kenmore41782052102Dryer
Kenmore41782052103Dryer
Kenmore41782142100Dryer
Kenmore41782142101Dryer
Kenmore41783042201Dryer
Kenmore41783042300Dryer
Kenmore41783052200Dryer
Kenmore41783052201Dryer
Kenmore41783142300Dryer
Kenmore41784042500Dryer
Kenmore41784052500Dryer
Kenmore41784082500Dryer
Kenmore41784092500Dryer
Kenmore41784152500Dryer
Kenmore41784252500Dryer
Kenmore41787042700Dryer
Kenmore41788042700Dryer
Kenmore41788052700Dryer
Kenmore41788056700Dryer
Kenmore41788076700Dryer