381251-1-S-Whirlpool-63907             -Suspension Spring
381251-1-S-Whirlpool-63907             -Suspension Spring

Suspension Spring

PartSelect Number PS381251

Sold Individually. Appliance takes 3 of this part.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Shakes and moves.
  • Unusual Noise.
  • Leaking water.
  • Compare At

    $3.02
  • You Save

    $.50
  • Your Price

    $2.52
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.8 / 5.0, 24 reviews What's this?
16-24 of 24
 

5 of 8 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsPliers, Socket set

CustomerJames from Nelsonville OH

Tub did not center and seal was hanging out of tub

Laid washer on front side and removed top spring, then lifted the tub assembly to replace the right side spring, the one behind the motor was the hardest, I lifted the tub then removed the spring bracket at the tub with pliers and a socket. The top seal all I had to do was take the 4 screws that hold the top on (it takes a long extension) then sit it bak up and I lifted the top up to give me enough room to unsnap the top piece of the tub, cleaned it up put seal in. The parts fit perfitlt and real fast shipping, I bookmarked the site and will buy from again. JIM

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerPaul from Milwaukie OR

Shaking on spin cycle

Removed the outside body of washer. Used 1/2 plywood between drum and wear pads to make space to pry out pads with screwdriver. Replaced suspension springs and tub spring (use waterproof grease on end of springs. Put washer back together and tested. Problem solved washer not walking all over floor anymore. Thanks for you help.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerChris from Bonners Ferry ID

Washer would walk all over when in the spin cycle

I tried to remove the outer console to get to the tub wear pads easier. This proved difficult for me for some reason. So I tipped the machine on its back at about a 45 degree angle. You will see the tripod support holding up the tub. The pads lie in between the bottom of the tub and on top of the tripod support . You won't be able to see the pads since the are on the top of the support, but you will see the two insert tabs of each pad sticking out. There are about 120 degrees apart from each other. I pushed up on the tub and slipped the piece of wood in between the tub and tripod support close to the pad. Taking a screwdriver and hammer I punched out the wear pad insert tabs. You can replace the old pad with the new one by using some force with your hands. Some pop right in and some you need to use a little leverage, maybe with the piece of wood you used to hold up the tub. Be careful not to get the pads greasy, keep clean as possible. Worked great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 7 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerRussell from Chicago IL

Out of ballance

removed two phillips screws from control panel. lifted panel to reveal two clips on both sides of machine. used flathead screwdriver to remove clips. tilted whole body up and away. pushed drum towards first spring and removed it . installation was reverse of procedure. did not fix it because basket had rusted at shaft bottom under agitator and put basket out of balance.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyDifficult

Time to do repair:30 - 60 mins

ToolsPliers

CustomerWilliam from Mokena IL

Washer tub off-balance during spin

This washer does not have a removable front panel, so the spring replacement was made from the bottom of the unit, with the washer lying down on its face. This put two of the springs in tension which had to be relieved by propping the tub. The springs had removable bottom clips which made the job much easier.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Socket set

CustomerNorman from Burlington NJ

During the spin cycle machine rocks the house

Replaced all of the springs. I put the shell back on and the problem still exists. I thought $20.00 was worth seeing if this would resolve the issue. I don't want to keep throwing parts at it. I noticed some black suit under the machine. I will be buying a new washer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Suspension Spring

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Wrench(Adjustable)

CustomerROBERT from ROCKY HILL CT

Washing moving all the time-lefth-to right all the time.

PULLED IT APART,LAYED IT DOWN AND LOOKED AT IT,AND CHANED THE 3 SPRINGS.AND IT IS LIKE NEW AGAIN.....

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Suspension Spring

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerStacy from Markle IN

Tub out of balance on spin cycle. Very noisy!

I the took washer to where I could lay it on its side.
Laying it on its side lets the suspension spring at the top go slack. Making pulling it from bracket easier.
Next , I lifted the tub up with a 2x4 and blocked it with another wood block. This let me have slack in the lower springs.
Of coarse I saved the hardest one (behind the motor) for last. I only swore a little! But got it to come out.
By the way, put in each new spring, before going on to the next one.
The new springs helped a lot, but I ended up ordering the wear pads a day or two later. They were very easy to replace. Just pop the old ones out of the frame with a screw driver. then pop the new ones back into the holes and you are done.
You may just want to buy them both and do it all at once. Saving moving the washer twice!

Help other customers find the most helpful instructions.

Were these instructions helpful?

61 of 1725 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:More than 2 hours

Tools

CustomerBOB from NIAGARA FALLS NY

Tub shacking back and forth

After seeing video it was easy . Took everything apart tub,basket,replaced all springs. Tub wear pads. It took longer because I cleaned eveything,took my time. There was a lot of deposits on tub and outer tub also some rust . Put it all back together all nice and clean . pluged it in put it in spin cycle and the motor just hummed. I than check to see if somethig was stuck no .Pulled motor tested it with out a load and did not work. Motor start winding went. Motor died. 2n one in 7 years. So I fixed that proplem I am a new owner of a Speed Queen washer and dryer .

Help other customers find the most helpful instructions.

Were these instructions helpful?

16-24 of 24