350868-1-S-Whirlpool-3951744           -Agitator
350868-1-S-Whirlpool-3951744           -Agitator 350868-2-S-Whirlpool-3951744           -Agitator http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/QEUHM0XA.gif

Agitator

PartSelect Number PS350868

This agitator comes with the 4 agitator dogs (cogs) and top mover. The cap is NOT included with the agitator.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not agitate.
  • Noisy.
  • Compare At

    $86.27
  • You Save

    $14.38
  • Your Price

    $71.89
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 38 reviews What's this?
1-5 of 38
 

326 of 373 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerDexter from Milwaukie, OR

Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose

After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go.

Help other customers find the most helpful instructions.

Were these instructions helpful?

25 of 31 people found this instruction helpful

Parts Used

  • Agitator

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerVincent from York, ME

Top section of agirtator not working

Removed top cap and one nut from agirtator then removed complete assembly. Replaced new assembly nut and cap.

Help other customers find the most helpful instructions.

Were these instructions helpful?

18 of 21 people found this instruction helpful

Parts Used

  • Agitator

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Socket set

Customerdoug from spokane, WA

Agitator was not working properly due to broken plastic pieces in agitator

First I removed the top of the agitator and then used a socket and ratchet to unscrew the bolt and put the new one on and tightened up the bolt, real easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 12 people found this instruction helpful

Parts Used

  • Agitator

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerSteven Lemons from Fort Greely, AK

Washing machine would not agitate clothes during cycles

first I removed the fabric softner and water seal from center of agitator, then I removed the bolt holding it on. All I had to do then is install new agitator with old bolt place water seal and fabric softner container back on and start washing clothes again. Very simple.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 14 people found this instruction helpful

Parts Used

  • Agitator

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Socket set

CustomerCHRISTI from NEWPORT NEWS, VA

Making alot of nosie while washing

First I removed the fabric softner dispenser. Then I removed cap took screw out removed agitator asseembly put new one in then I put screws back in.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 38