Models > 2DLSQ8000JQ4

2DLSQ8000JQ4 Whirlpool Washer - Overview

Get Parts and Repair Help for 2DLSQ8000JQ4

If you know the washer repair part you need, you can browse the list of all parts on the 2DLSQ8000JQ4, or you can search by name or part description. You can also find your part by where it is located on the 2DLSQ8000JQ4 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 2DLSQ8000JQ4 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.69

Agitator Directional Cogs

These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.

Order within the next 5 hrs and your part ships today!
$10.86

Direct Drive Motor Coupling

This coupling kit is used between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added strength.

Order within the next 5 hrs and your part ships today!
$28.99

Direct Drive Water Pump

It is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.

Order within the next 5 hrs and your part ships today!
$2.58

Suspension Spring

Sold Individually. Appliance takes 3 of this part.

Order within the next 5 hrs and your part ships today!
$26.31

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity wash...

Order within the next 5 hrs and your part ships today!
$14.14

Water Inlet Valve with Mounting Bracket

This part could have either a blue colored valve body or a green colored valve body. There are two ports for water to enter and this valve is compatible with a half inch ID hose. It has two 3/4-11x1/2 NHT hose threads.

Order within the next 5 hrs and your part ships today!
$6.82

Agitator Cam Kit

This kit included the cam, 4 dogs and bearing.

Order within the next 5 hrs and your part ships today!
$4.54

Agitator Bolt

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

Order within the next 5 hrs and your part ships today!
$3.84

Tub Spring

Order within the next 5 hrs and your part ships today!
$2.88

Inner Cap Seal

Also known as an O-Ring.

Order within the next 5 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No movement from Basket & agitator

  • Customer: Jeff from Wayne NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 567 of 601 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor co... read more

REPLACE WATER PUMP COUPLING

  • Customer: RICHARD from PHILA PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 545 of 560 people found this instruction helpful
REMOVED CASING TIP OVER WASHER DISCONNECTED WATER PUMP. DISCONNECTED MOTOR THEN REPLACE COUPLING THEN REASSEMBLE MOTOR THEN REPLACED WATER PUMP. read more

washer wouldn't agitate

  • Customer: mike from Kent WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 535 of 549 people found this instruction helpful
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing usin... read more