350868-1-S-Whirlpool-3951744           -Agitator
350868-1-S-Whirlpool-3951744           -Agitator 350868-2-S-Whirlpool-3951744           -Agitator http://www.partselect.com/Schematics/Maytag/QEUHM0XA.gif

Agitator

PartSelect Number PS350868

This agitator comes with the 4 agitator dogs (cogs) and top mover. The cap is NOT included with the agitator.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not agitate.
  • Noisy.
  • Compare At

    $100.58
  • You Save

    $16.76
  • Your Price

    $83.82
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 38 reviews What's this?
 

8 of 12 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Robert from Whiteman AFB, MO

Upper agitator would not turn

First I removed the fabric softener dispenser. I removed the inner cap seal and agitator retaining bolt. Then I firmly pulled up on the agitator to remove the complete agitator assembly. I replaced the inner cap seal and installed the new agitator bolt with rubber washer. I placed the new agitator assembly on the drive shaft and tightened the bolt. Lastly I installed the inner seal and the fabric softener dispenser. The total time spent was around 10 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 10 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Linda from Enola, PA

Two fold: Agitator slipping, washer delays spin cycle untill lid is raised and dropped.

First repair was easy, remove center bolt, pull up on agitator and replace entire unit as one piece, replace bolt and liquid dispenser.

Second repair was more difficult in that I could not immediately find the release to remove timer control. After removing 5 screws unnecessaryily and studying unit more closely, tried prying up on little tab that has a "+" symbol on it that locks into a little hole. While holding up on that tab, slide timer unit sideways and unit falls out of washer panel. Simply slide the new unit in and it locks in place.

Also the directions to remove the knob were convienently printed on the orginal and replacement timer, but an ARROW pointing to the black tab on rear of the timer control would be helpful as I mistook the tab to be on the front side under the knob from studing the replacement and tried to pull the smaller inter knob off in order to push it in to release the larger outside knob portion in order to disconnect the timer. No harm done, eventually figured it out, but it still didn't fix the problem. As the washer will EVENTUALLY go in the spin cycle without picking up and dropping the lid, I'm assuming the lid switch is defective, although it appears to work otherwise. Any other possible soulutions appreciated.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 9 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Socket set
Customer: David from Mission Viejo, CA

Top half of agitator not working

Although this was listed as 'a bit difficult' and talking a bit longer than normal, this was because the agitator cap had leaked, and over time the agitator bolt had become completely rusted such that a socket simply couldn't fit. Due to the tight confines, I also could not get a needle-nose vise-grip to hold on to the nut, so attempted to drill out the bolt. This ended up being a problem, but it turns out that drilling AROUND the edge of the bolt and through the edge of the plastic allowed me to remove the top of the agitator, which then allowed a normal pair of vise-grips to be used to remove the bolt. Once the bolt is removed, everything simply fell into place, and the overall job 'should' have only taken a couple of minutes and been 'really easy', except for that rusted-out bolt.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 10 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers, Socket set, Wrench set
Customer: Rich from Arnold, CA

Washer top adgitator / frig. Ice maker not producing

Washer; I watched the repair video, and replaced the agitator. It was so simple I think that it took longer to watch the video. Refrigerator; I replaced the ice maker, and the solenoid valve. It was very easy to replace the parts, however it took a while to diagnose the problem. I found an appliance repair man that told me what contact points on the front of the ice maker would trigger the clock (so I didn't have to wait for an hour for the clock to activate). There is also a set of contacts that when jumpered will trigger the solenoid valve. It only took a total of 25 minutes to fix both the washer, and the dryer. If you take a piece of 14 Ga. solid wire about 6" long and strip the ends about 3/8" and bend it into a U you have a jumper. If you jump the contact points on the front of the icemaker letters T & H this will start the clock operation. If you jump letters L & V, the solenoid should open to allow water to flow to the tray. If water does not flow, the filter should be checked in the valve. If the valve sounds like it is opening, sometimes the inlet to the ice maker can freeze stoping the flow. In my case I found the solenoid valve was getting only a week signal, and would only function about 25% of the time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used:
  • Agitator
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Socket set
Customer: Joseph from Jupiter, FL

Partial agitation - cam agitator teeth worn

1. Removed the fabric softener dispenser

2. Removed Barrier Seal Cover

3. Removed bolt and seal

4. Removed and replaced CAM Agitator Assembly

5. Reversed the removal steps.

Help other customers find the most helpful instructions.

Were these instructions helpful?