Agitator Repair Kit

PartSelect Number PS334650

The agitator kit is most commonly used if the top part of the agitator is not moving correctly but the bottom is. This kit now includes all pieces shown in photo plus the thrust spacer, inner cap seal and agitator bolt washer. May need agitator grease for repair.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not agitate.
  • Unusual Noise.
  • Pumps but will not spin.
  • Shakes and moves.
  • Spins slowly.
  • Not cleaning properly.
  • Compare At

    $21.44
  • You Save

    $3.57
  • Your Price

    $17.87
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Agitator Bolt

Part Number 348478

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$4.46
In Stock

Inner Cap Seal

Part Number 1490170

Also known as an O-Ring.

$2.18
In Stock

Thrust Spacer

Part Number 334562

This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is used in the agitator assembly of many direct drive washing machine models. This is the retaining ring for inside of agitator. May need agitator grease for repair.

$2.52
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 336 reviews What's this?
76-90 of 336
 

1 of 1 people found this instruction helpful

Parts Used

  • Agitator Repair Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Socket set

CustomerRandy L. from Wallingford CT

Top of agitator did not turn

removed fabric softner tub,pulled out cap, unscrewed nut that holds agitator , pulled apart top of agitator and replaced dogs that were worn out and broken, reassembled in reverse order, no problem easy to do took 15-30 mins.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Agitator Repair Kit

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsSocket set

CustomerRonald from Binghamton NY

Agitater-softener dis pensor wasnt working properly,just spinning

took agitater off with socket,removed old parts,installed new kit,lubed neccassary parts,reinstalled and tested works like a charm.I was really surprised at the delivery time,I ordered the parts on monday evening,wednesday morning they were here,thanks guys

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Agitator Repair Kit

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerStacy from temple TX

Agitator started to make a popping noise and the top would not turn.

Took the fabric softner dispenser off and removed the water barrier seal and removed the bolt. Lifted the entire agitator off and laid the parts out how they came off the washer. took out the new partns and lined them up next to the old ones and replaced. Put the agitator back together and slid it into place on the washer and tightened the bolt. Then I replaced the O-ring on the water barrier and pushed it into place. Works fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsSocket set

CustomerGerald from Delavan WI

Only one part of the two part agitator worked

I removed the softener dispenser and the cap from the center of the agitator. With a socket set I removed the bolt holding the agitator. pulled off the agitator. I could see the worn "ratchet fingers". I ordered the parts and two days later received them. Following the enclosed instructions I fixed it. First time I have ever fixed anything on a washer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Agitator Repair Kit

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerRaymond from Standish MI

Agitator was not working cam dogs were broke off

Repair was quite easy, I followed the instructions sent with the repair kit, even thow I pretty much knew what to do because I had had it all apart to find out what the problem was. First took screwdriver and gently pryed off softner dispenser, pulled out cap and seal, remove agitator bolt pull up on auger, remove old agitator cam and replace with new, reassemble unit. the repair kit was received quickly from Parts Select and for what I feel was a good price, thank you!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Agitator Repair Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerMichael from Champlin MN

Auger slipping/noise

Noticed a clunking sound in the washer, and got worried that I needed a new washer. I watched the washer in motion and noticed the auger slipping. I took the auger/agitator assembly apart and inspected the parts (dogs completely worn). Did a a Google search for my make/model replacement parts - and PartSelect popped up. I read the repair stories on my washer and purchased the Agitator Repair Kit. I received the kit four days later and began the install.

The included directions tell you everything. The toughest part for me was pulling the bearing down on the agitator cam - I just didn't want to break the plastic bearing.

No more noise, and the auger is working just fine. A quick and simple fix, and with purchasing the repair kit, I also replaced a couple other parts that showed signs of wear compared to the new ones.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerDave from Rock Springs WY

Top of agitater not moving

loosened half inch bolt that held agitator in place. removed old and dropped in new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Agitator Repair Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerStephen from Mesa AZ

No agitation

Removed liquid dispenser from agitator. 7/16" deep socket on extention to remove bolt holding agitator assembly. Assembled the repair kit into the old agitator, put new washer on bolt and installed. Took longer to clean the parts then to make the repair... Thanks for the great website.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Agitator Repair Kit

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Wrench set

CustomerMarcel from Houston TX

Agitator would not push clothes down

Overall, the repair went very easy. About the biggest problem was figuring out how to remove the plastic cap which allows access to the long bolt which holds the entire agitator assembly the motor shaft. But once it was disassembled the rest of the repair was very straightforward. The repair instructions which came with the repair kit was very helpful.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Agitator Repair Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsSocket set

Customerleeanna from port orchard WA

Top part of agitator would not agitate

very easy directions. undid nut with socket pulled top part out. and replaced with new piece i got in kit. took around 15 minutes or so.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Agitator Repair Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerEDUARDO from FARMINGDALE NY

Top agitator does not turn when mach is running

first removed the top dispenser[softener]by twisting it up.then pry out the round plastic cover that comes with the oring.after removing the cover
you'll see the 3/8 bolt that holds the agitator cam.removing the 3/8 bolt ,you can easily removed the whole agitator assembly and replaced it with the whole kit.on my washing machine the problem is the agitator cam 4 cogs[refer as dog ears,it is worn out completely.replaced it with the whole kit eventhough the problem is only the 4 cogs.the price of the kit is very cheap,and parts is delivered in short time.reminder,put locktite to the bolts thread before installing it back.easy less than 15 minutes installation.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Agitator Repair Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerROY from Milton-Freewater OR

Teeth on cloths agitator rotator dogs were worn off

I popped the top off the agitator assembly which exposed a sealed cap. I pulled the cap off with my fingers which exposed a 7/16 bolt head. Using an extension on my ratchet and 7/16" socket, I loosed the bolt and used a small magnet to pull the bolt out which released the agitator rotator. I assembled the kit as per instructions and inserted it into the agitator. It is important to line up the slots on the sides of the agitator. I replaced the bolt, the seam cap and agitator top. I did not use the replacement o ring as it was larger than the one that existed and would not fit. It took around 15 minutes total.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Agitator Repair Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerLARRY from HANOVER MD

Won't agitate

remove the agitater cap, then the seal. They both just pull up by hand. Then remove the bolt. Take out agitater. Remove old dogs and dog cup. Reverse order to put back together. It is the easiest repair you can do to a washer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Socket set

CustomerErick from Ovid MI

Top agitator stopped moving

The "Agitator Repair Kit" worked perfect; it is like a brand new machine again. There was only one bolt to remove and the entire agitator assembly came out. Once removed, I separated the top corkscrew portion from the bottom agitator. The old dog-ear ratchet pieces were worn smooth and were not gripping the inner teeth on the upper portion of the aggitator so I simply replaced all the parts with the new ones from your kit and reassembled. In under 15 minutes, my machine was working like new!!! I cannot even imaging how much a repairman would have rocked me for the same repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Agitator Repair Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerJosef from Ocean Side CA

Agitator would slip during heavy loads

The repair was easy in large part to the very clear directions furnished with the agitator repair kit. Pop the cap on the agitator by slipping a small screw driver in the small slot at its base. You then reach in and pull out an inner seal--it has little handles to grab...the toughest part is that it is a tight fit for larger hands inside the agitator tube. I thought about getting the wife to do it, but I finally got it. This exposes the connecting nut. You will need a socket wrench with about 8-10 inch extension to reach the nut that secures the augur (upper agitator) to the lower agitator. Then just follow the directions to replace the dogs, thrust washer, and sealing washers. Reassemble and use plenty of soap to lube the large inner seal, and be sure it seats firmly and squarely in the agitator tube. Easy job and runs like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

76-90 of 336