Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS334650
The agitator kit is most commonly used if the top part of the agitator is not moving correctly but the bottom is. This kit now includes all pieces shown in photo plus the thrust spacer, inner cap seal and washer. May need agitator grease for repair.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
Also known as an O-Ring. This black o-ring seal is three inches in diameter.
This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is used in the agitator assembly of many direct drive washing machine models. This is the retaining ring for inside of agitator. May need agitator grease for repair.
The most difficult aspect of the repair was separating the upper and lower agitator, as over the years the minerals in the water had stuck them together. I used a rubber mallet and gave the auger a few sharp blows, and the two main pieces separated. The greatest amount of time involved was the process of meticulously cleaning all the parts that were to be reused in the repair as there was a lot of old grease, dirt and mineral build up coating everything. The old cam dogs were completely gone, they had disintegrated over 20 years of use. I simply dropped the four new dogs in their cut outs on the cam agitator. and snapped on the bearing collar, which is really just a plastic retaining ring that prevents the dogs from falling out when you turn the cam agitator upside down and push it into position to connect the two agitator sections. The new thrust washer easily set in place on the lower agitator, and bolting the assembly back onto the washer shaft was a snap with a 10 inch socket extension. Washer works perfectly now, it spins better than the average political pundit.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Follow inst. that came with the parts. Took out the old and replace with the new one's. Took about 30 mins. all total. Web site was real good on showing which parts that I needed and order department was great. Wayne Tulloch
Repairing the agitator was easy.Removed the upper housing and 1 bolt.Change the ratcheting mechanism, reinstall, done.Changing the pump was a bit more involved.Had to remove the shell.The old pump was rusted on to the motorbut with the help of some PB Blaster, screwdrivers and a hammer I was able to get it off.No more leaks on the floor and the clothes actually agitate instead of remaing stationary.For less than a Plumbers 1 hour of labor I was able to repair it myself and will probably get another 5 years out of this washer. Will it ever die?
I am a maintenance mechanic and was very easy for me. I just loose i screw 10mm took out old parts put new parts in and it was ready to go again.
Gravy replacement! I pulled out softner dispenser,undid the one bolt securing the agitator assembly, and removed the top half of the agitator. the cam assembly tapped out. I replaced the bolt so I could still use the machine while the parts were on the way. When the part arrived (36 hours later with 3-5 days expected) I removed the bolt again and followed the simple instructions to replace the cam. Saved a ton on repair costs!
I removed the fabric softener dispenser atop the agitator. I twisted and pulled out the plug inside the agitator. Using a socket on an extended wrench, I removed the single nut inside the agitator (keep the agitator from turning with a large screwdriver, etc. and turn the nut counter-clockwise to remove). The agitator came out, and I removed all of the cam parts. I cleaned all of the old parts with bleach and water. Reinstalling the new parts was simple and straightforward as indicated in the illustrated instructions. Now it works great!
First I removed the housing to gain access to the water pump. Upon removal of the clamps holding the rubber hoses, I used a shallow pan to collect the water in the system (2-3 cups). Next, a flat tip screw driver was used to pry off the water pump retainer clips, such action permits the pump to be easily withdrawn from the motor shaft. Prior to my parts purchase, I had noticed rubber particles below the transmission which was due to a worn motor coupling. My second service step was to use a socket wrench to loosen the motor retaining clips for motor removal. The coupling was replaced, although the plastic driven "gears" were left in place and not replaced given they were observed in good condition and not easily removed with hand tools. After coupling installation to the transmission, the motor drive was aligned to engage the coupling. Alignment pins for the motor helped with such alignment. The motor retention clips were reinstalled and tightened - important to check the overall alignment here. Next, the rubber hoses to the pump were connected to make the final assembly step back to motor easy. Last the pump was resecured with the clips. The agitator was repaired by removal of the softener dispenser - pulling and twisting up. Next a deep well socket was used to remove the agitator bolt. The agitator was lifted off easily. Finally, using the instructions provided a new thrust washer was installed, the agitator cam and cam dogs were installed followed by reassembly of the agitator. The agitator bolt was installed and tightened. The cover plate residing inside the softener dispenser was reinstalled, followed by the softener dispenser itself. The new parts are all now installed....last reassemble the outer housing to the washer...everything works great now.
I popped the cap off the agitator removed a bolt. Removed the damaged parts. And replaced them with the new ones it was easy.
I removed the agitator top cap first. I reached inside and removed plastic cap. I then removed the 7/16 bolt inside the agitator and lifted it out of the machine. I put my foot on the bottom part of the agitator and pulled the top part off. I removed the plastic bushing in the bottom part and then removed the plastic bushing with the dog ears and the bolt. I used some appliance grease on the bushing on the bottom part and slid the top part of the agitator back in place and replaced the 7/16 bolt. It worked like a charm. My wife says I'm her hero. Thanks for making it so easy.
Repair was extremely simple by using the video provided online. Works perfectly! Thanks so much.
Removed top agitator bolt lifted agitator out and replaced ring and geared dogs. replaced Agitator top swirl vanes. It would have been nice if the kit included agitator grease and a new bolt and washer.
Couldn't do the repair due to receiving incorrect parts used what I could from kit to replace parts. The repair kit said it would work on my machine but did not. Now I will have to purchase a complete aigator to fix hopefully the issue.
After calling repair services locally and getting outrageous estimates, just to come and see and telling it will cost at least upwards of $ 150.00, decided to look at fixing it myself. Did not want to buy a new unit, as we are building a new house and wanted time to evaluate a new pair later next year. I wanted to put this unit in the garage of the new house, Partselect site was very informative with the symptoms of the problem and required parts and the best feature was the "how to videos". Watched the videos twice and decided I will give it a try. Ordered the parts, which came promptly despite the Thanksgiving holidays (I had to just handwash some essential clothes only once). Watched the videos again and replaced the cam dogs, which we're completely worn out and in pieces. Next replaced the motor couplings. Had a hard time putting back the washer cover, as I had to jiggle it to align. Washer Works like a charm. Saved $$. Partselect should consider bundling the agitator grease with cam dogs. Did not use any grease as I had none. Overall great satisfaction. Thanks.
Only had to replace the dogs, the remainder of the kit did not fit my washer. It now works like a dream, maybe better than before and since I did it myself I am very proud to have made the repair and did not require a $80+ service call. I pulled off the softener dispenser, used an 11/16" socket, removed the agitator, set it on the floor stood on it and pulled off the top of the agitator, removed the device that holds the dogs, put the new ones in and reassembled. It was super easy!
Took sealing caps off agitator to access holding screw & followed instructions included with the repair kit to replace agitator unit. Ordered the part on Friday morning and had the part by early Monday morning. Impressed with the service........Thanks
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.