271084-1-S-GE-WH1X2708          -Knob and Clip
271084-1-S-GE-WH1X2708          -Knob and Clip 271084-2-S-GE-WH1X2708          -Knob and Clip 271084-3-S-GE-WH1X2708          -Knob and Clip

Knob and Clip

PartSelect Number PS271084

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $30.24
  • You Save

    $5.04
  • Your Price

    $25.20
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.8 / 5.0, 4 reviews What's this?
1-4 of 4
 

6 of 7 people found this instruction helpful

Parts Used

  • Knob and Clip

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerTERRY from OMAHA NE

Broken knob

replaced wash selection knob. Right part in the right place "clicked" into position and works fine.

Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Knob and Clip

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerE Robert from Bellingham WA

Several teeth on knob that turns timer had broken off.

First I unplugged washing machine. Then I removed the four screws on top of panel above panel, this made it easier to see the clip that hold the knob onto the timer shaft.
Then I pushed clip off and removed knob. New knob came with a new clip in which all to do is push the knob onto the shaft until it clicks into place. Align panel back in bracket and put screws back in.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Knob and Clip

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerKevin from Lords Valley PA

The wash selector knob broke off.

It was verey easy to remove the broken part of the knob by removing the little clip that holds the know on the post. Then I just had to insert the new knob on the post and push it down til it clicked in place.

I had originally removed the back splash but that was not necessary. Everything can be done from the front panel of the washer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJoseph from Avalon NJ

Timer was loose, and became impossible to pull out to stop. Washer knob then broke at teeth.

I took out the four screws with Allen wrench, and saw that the timer plastic had broken where the screw held it tight to panel. Then I went to Parts Select website, and entered model number. Immediately got schematics and part numbers needed to effect rescue mission. Ordered the parts with expedited delivery, and within 36 hours the parts were here and ready to install.
Since the timer knob was already broken as well as the plastic around the hold-down screw, all that remained to do was disconnect the ground and the wiring harness. Old timer was out.
New timer ground connected, wiring harness slid easily and hold-down screw connected with a nut-driver. Slip in the three metal flanges into the slots on top of the washer, tighten down the four allen head screws, move the washer back into place, plug it in and done. Less than 30 minutes total.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4