249424-1-S-GE-WB44X200          -Bake Element - 240V
249424-1-S-GE-WB44X200          -Bake Element - 240V 249424-2-S-GE-WB44X200          -Bake Element - 240V 249424-3-S-GE-WB44X200          -Bake Element - 240V http://www.partselect.com/Schematics/GE/GE_Thumb/00006230i02.gif

Bake Element - 240V

PartSelect Number PS249424

This bake element kit comes with two installation screws.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Element will not heat.
  • Oven not heating evenly.
  • Will Not Start.
  • Oven is too hot.
  • Little to no heat when broiling.
  • Touchpad does not respond.
  • Compare At

    $38.42
  • You Save

    $6.40
  • Your Price

    $32.02
In Stock
Order within the next 4 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 169 reviews What's this?
 

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Wrench set

CustomerNancy from Burlingame, CA

Burned out oven element

we of course turned off the power. the box wrench loosened the nuts. the part fit easily in our 30 year old oven. It was easy to attach the leads to the heating element--a bit awkward, but we finished the job in 20 minutes. At first, the new element looked different from the old one, but it fit perfectly. The oven is as good as "new" needs cleaning!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerWilliam M. from Towaco, NJ

Bake element went dead

Removed access screws from bake element cover, removed screws retaining wire connections on bake element, reverse procedure, and heat to burn off contaminants.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerMichael F. from Bloomfield Hills, MI

Baking element burned out

remove/replace baking element. Relatively simple to do; however, I used the old screws/nuts as they worked better than the new ones which were included.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

Customerderek from lynchburg, VA

Fireworks! Element blew explosively. Loud noise, major arc. Smoke and blew breaker.

First job was power off! Next step was to remove the two screws holding the element to rear wall of oven. Next is was to gently pull the wires through the hole as far as possible. At this point I needed pliers to stabilize the joint while I removed the two screws of the electrical connection. Now it was easy to clean the oven to remove arc residue. Now it was a matter of reassemble. Hardest point was getting the screws started in the electrical connections without cross threading while reaching in over the door. Use pliers to ensure you don't bend the connection wires on the element. Finally remount the element with the two original screws. This was the second element to fail. Last time I removed the oven door for better access. I think it was quicker with door on but a lot more bending and reaching.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerLaurence from Durham, NC

Element bad

New element arrived in a couple of days! We turned off breaker to oven, removed the old one which only involved two screws. Then we had to connect new one and re-attach metal square, only tricky part was getting the metal square positioned correctly but that was really not hard, just made sure insulation was covered and plate went back in same position. If we had called a eepair company it would have taken a week or more and probably been expensive!

Help other customers find the most helpful instructions.

Were these instructions helpful?