Models
>
JK14*08
JK14*08 General Electric Range - Overview
Sections of the JK14*08
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Bake Element - 240V
PartSelect #: PS249424
Manufacturer #: WB44X200
This is a 240 volt bake element for your oven or range. The kit comes with two installation screws and the element. The element functions by supplying heat from the bottom of the oven to bake or cook ...
$45.72
In Stock
Broil Element
PartSelect #: PS249411
Manufacturer #: WB44X173
The broil element is located at the top of the oven and gives off heat in order to bake evenly. If you notice that the element is not heating up or is not cooking evenly it could be because it is brok...
$31.03
In Stock
Broiler Pan - Large
PartSelect #: PS1517612
Manufacturer #: WB48X10056
This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain. The grate measures ...
$30.07
In Stock
Oven Sensor
PartSelect #: PS235718
Manufacturer #: WB21X158
This sensor offers 16 ohms of resistance at room temperature, though the resistance increases as the temperature increases.
No Longer Available
Questions And Answers for JK14*08
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JK14*08
[Viewing 7 of 7]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replacment of the bake unit
The hardest part was removing the old nuthead screws off the old bake burner. Once those were off installing the new bake element was simple. One screw in each wire terminal, two hex head screws to hold the unit in place. Works like a charm!
Parts Used:
-
Beth from Matthews, NC
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Socket set
609 of 623 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven lower burner burned out
Very easy, remove two screws, pull burner unit out slightly, then remove the two screws attaching the wires, one to each side, remove old unit and replace with new unit and replace screws.
Works fine perfect replacement.
Works fine perfect replacement.
Parts Used:
-
james from franklin, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
507 of 590 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake element was on its last legs, starting to crack but still functional.
Removed the racks, unscrewed the back plate which holds the element, unscrewed the leads from the element, removed the old part.
Reversed the process to install the new element.
Turned the oven on for a few minutes to burn any contaminates off the new element, replaced the racks.
And that was it; quite ea ... Read more sy.
Reversed the process to install the new element.
Turned the oven on for a few minutes to burn any contaminates off the new element, replaced the racks.
And that was it; quite ea ... Read more sy.
Read less
Parts Used:
-
Lawrence from San Jose, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
223 of 373 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!