243701-1-S-GE-WB2X9719          -Single Heating Element Support Clip
243701-1-S-GE-WB2X9719          -Single Heating Element Support Clip 243701-2-S-GE-WB2X9719          -Single Heating Element Support Clip 243701-3-S-GE-WB2X9719          -Single Heating Element Support Clip

Single Heating Element Support Clip

PartSelect Number PS243701

This metallic clip is used to help support the broil element. Sold individually.

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $5.12
  • You Save

    $.85
  • Your Price

    $4.27
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 12 reviews What's this?
1-12 of 12
 

5 of 7 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Socket set

CustomerPaul from Canton NY

Broiling element had burned through, req. Its replacement

First I removed the two screws that hold the element in place. I also removed a screw that held one end of a support bracket. I then pulled the element out about 3 inches and disconnected the two wires. Reversing these steps, I finished the element's replacement.

I had noticed that the former element was sagging at the front end. I installed the additional clips (not original) on each forward end of the element for additional support.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set, Wrench(Adjustable)

CustomerHarald from Port Washington NY

Dryer old and worn out

Dryer started making noises years ago. Finally it was intermittently starting, then...didn't start at all. It made a buzzing noise, like the motor was in over-torque. Then it over heated and wouldn't do anything until it cooled down. Then the cycle started all over again. I thought it best to change out all the worn parts. Found the belt, the rear seal, the rollers and motor all needed to be replaced. All were very simple to do. Followed the instructions and videos from others located on this site.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerStanley from Sulphur OK

Bake element bad

Inside oven, remove two screws that hold element to back wall, pull element out three or so inches to get to wire clip connections, unclip wires, remove bad element, put new element in in reverse order of taking out bad element, just that simple. Also this site was so easy to use, plus the shipping time was unbelieveably short, even a company service man couldn't have been that quick, or as reasonable. Thanks a bunch!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerGerald from Redondo Beach CA

The upper element for broiling went kaput!

The two dollar socket set from Xmas 20 years ago had the right size socket..

Long arms are advisable.

The lower element still plugged in while the upper wires were just hanging there surrounded with fluffy white insulation fuzz, I wondered, " Could I bake a potato for my yearning and hungry family?"

When I explained the situation to my retired father in Arizona he said simply, "I wouldn't."

The new element popped in. It got really red, and, kinda like watching my toaster toast, the show was pretty much over after it heated up.

Shalom and Merry Christmas Folks!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerANNE from FT. LAUDERDALE FL

Broiler element would not work.

Removed the old element: removed clips holding the element, unscrewed the 2 screws that hold element in place. On the back of the range, removed casing to get to the connection wires, disconnected the element then removed the element. Reversed procedure to replace. Thanks for the speedy ordering and delivery.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Single Heating Element Support Clip

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerJames from Hedgesville WV

Heating element clap broke off

All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerJoseph N from Hazletownship PA

Rusted burn box

I simply removed drop in range and removed screws holding burn box and installed new box. Total time was approxmately !hr.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Single Heating Element Support Clip

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerDoris from Aberdeen NJ

Hanging broiler

Quick and easy, thanks!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerJim from Arlington MA

The bake elemement burned out & the clips for the top element were broken

The bake element basically just plugs in remove the two screws in the back with a nut driver pull the element out unplug the spade connectors and reconnect the new element . As far as the clips just snap them on to the top element and snap back in the holes at the top of the oven.
Also very fast delivery less then 48 hours from ordering to delivery

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Single Heating Element Support Clip

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerVictor from Miami Beach FL

Heating element dangling

Snapped in the clip

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerReba from Pleasanton, TX

Baking element cracked and would not heat

I turned off the electricity to the oven.and removed the door.
I removed the 2 screws with a nut driver holding the element in place, pulled the element out about 3 inches and disconnected the two wires with pliers , clamped the 2 wires together to keep them from falling in the back of liner.
When the new element was received the procedure was reversed. Electricity was restored and the oven works perfectly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used

  • Single Heating Element Support Clip

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

Customertomi from dallas TX

Support clips fell out

Parts Select is the only parts place I found on the internet that had what I needed on my first purchase, so when I needed these clips I naturally went back to them. Product was easy to find, price was fine, receipt for payment quick and more importantly receipt of item was super quick. Thanks to the efficiency of this place and my old appliances, I will continue to go to them as needed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-12 of 12