| |
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerFrank from Playa del Rey CA
Upper basket rollers and support were broken/worn out
I pried out the roller channel end cap then removed entire basket. The four rollers were installed and snapped back into place. The roller channel end caps were then replaced and the basket is just like new.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerNicholas from Navarre FL
Broken rollers on top rack
parts fit right and job went smoothly
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJon from Depoe Bay OR
Rack roller broke and the rack sagged
Last time I had to replace a rack roller, I broke the end cap trying to get it out. This time I watched the repair video at Part Select, followed the instructions, and voila. Used a screwdriver to bend the tab on the end cap and took it our at an angle, removed the other end cap, rolled the rack out, unclipped the roller, clipped the new one on, replaced the rack and installed the new end caps with a push in design. Done.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJoyc e L. from Prosser WA
Rack kept coming off slider due to broken end
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers
CustomerJohn from Shrewsbury VT
Broken upper rack rollers and missing end cap.
Removing the end cap required some force and because of it's age and the amount of heat it has seen it broke right away
I ordered new ones for each side because I thought this might happen. The new ones went on by lifting the inner tabs to snap into the rail.
Changing the rack rollers was very easy and took minutes. Use some vegetable oil on the rollers to get them to move easier in the rails.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerWilliam from Auburn CA
Right front rack roller broken.
Removed old end cap and then easily slid replacement roller in place on top right rack slider. Took time figure out how to get end cap to fit, but finally it worked.
Worth it!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
Tools
CustomerTracy from Rockland MA
The top part of the dishwasher down to bottom
first i see if i could move the metal piece it wouldn't move si i used a flat head screw drive to fix it . the end piece was to long so i cut a piece off it fitting it is not moving
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerAbigail from Glendale MO
The top rack of the dishwasher had lost it's rolling devise
It was amazingly easy to repair, I popped the old attachments off and snapped the new ones on in less than 5 minutes, I wish I had fixed my dishwasher earlier, had I known I could repair it by myself!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerCynthia from Raleigh NC
Broken upper rack rollers and front end rail caps
First I removed the older/broken rack rollers and very easily inserted the new rack rollers. Then I used a pliers to widen the rail end so the cap could fit in easily. Once the rail end was widened it was pretty simple to replace the rail end cap and pinch the rail end back into place with the pliers.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
Tools
CustomerMary Beth from Whispering Pines NC
The end cap came off the upper rack
Super easy..........just push it on and it should snap in place. No tools required!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerThomas from Northeast MD
The plastic rollers on the top shelf broke off.
You need to carefully take off the end caps (which I broke), pull off the rack rollers/ snap the new rack rollers on, and carefully place the end caps back on.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerChristina from Claremore OK
The end cap broke off so when we would pull out the upper rack the whell would fall off of the track.
The end cap snapped into place perfectly without any problems and the rack works like new again. This is the second time I have used PartSelect.com and I am very satisfied with how fast I recieve the product and the easy of finding what I need. I would recommend them to anyone!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerTimothy from Chatham NJ
Discovered that the end caps were broken
Removed the broken items and clicked the new ones in place utilizing a pliers
|
2 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
Customerdavid from portland OR
Rack rollers were broken, so the upper tray didn't work
I removed the end caps from one end of each slide, then put the rack rollers on the slides, snapped the rack rollers onto the tray, installed the tray in the machine, put the end caps on the slides, and voila, done.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
Tools
Customerdonna from walworth NY
Upper dishwashr rack lost the end cap and the rack kept coming off the track when you went to push it back in it would jam into the track and all the dishes would bang and fall.
placed the end cap into location and forced it into place. Fixed -and we are all much happier!!
|