2201441-1-S-Whirlpool-Y703147-Infinite Switch
2201441-1-S-Whirlpool-Y703147-Infinite Switch 2201441-2-S-Whirlpool-Y703147-Infinite Switch 2201441-3-S-Whirlpool-Y703147-Infinite Switch http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/33390.gif

Infinite Switch

PartSelect Number PS2201441

This switch has a double-flat shaft that is 1" long. This switch is palnut-mounted and the 'off' position is at the top.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Element will not heat.
  • Will Not Start.
  • Compare At

    $61.81
  • You Save

    $10.30
  • Your Price

    $51.51
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Palnut

Part Number 2177497

$15.40
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 21 reviews What's this?
1-5 of 21
 

25 of 30 people found this instruction helpful

Parts Used

  • Infinite Switch

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench set

CustomerMalcolm from White House, TN

Burner switch broke were knob attached

First I cut off power supply, removed screws that held panel on, pulled the switch up and disconnected wires. Installed new switch, being sure to connect wires in the correct places. Refastened panel to stove top. Turned power back on and tested switch and it Worked.

Help other customers find the most helpful instructions.

Were these instructions helpful?

19 of 21 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerDonald from Bloomington, MN

Fan switch stiff and shorted burner control, scratched up escut plate

1st-turned off power to stove top, then removed 2 screws to loosen the control panel. 2nd- I removed the shorted infinite switch by using a pliers to loosen the nut holding the burner in place, undid the electrical connections (noting where each was attached to the old control) and reattached them to the new control. Then I undid the nut holding each of the other 3 burner controls, detached the wires to the old fan switch, reattached the wires to the new fan switch, i removed the red idiot lights (by moving them sideways) from the escut kit. I then reattached everything to the new plate, secured the panel to the stove top, turned the juice on, And it worked as it should, and the new plate made the stove top appear almost new. 30 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 12 people found this instruction helpful

Parts Used

  • Infinite Switch

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench (Adjustable)

CustomerLansing from Alamo, CA

Two heating elements couldn't be controlled - full on

Turned off power.

Removed two screws to free up section of cooktop containing 4 switches - 2 good, 2 damaged. Removed the dials from top of the 2 damaged switches. With an adjustable wrench, loosed nut on stem of switch that fastened switch to assembly. Noted which of the 5 wires on each switch went on which tab. Pulled off 5 wires on one switch, finished removing the nut and removed broken switch. Put in new switch, attached the nut, and replaced 5 wires in exactly the same position, Tightened nut. Replaced dial. Repeated procedure for second switch. Placed section containing the 4 switches back on cooktop and inserted/tighted 2 screws holding it in place.

Turned on power.

Told cleaning people to NEVER put aluminum foil under the burner units again. The foil shorted across the power and damaged the switches.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerDeborah from Newburg, MD

Control switch broke off at the knob

My husband actually did the repair and it went very smootly. He removed the palnuts on all switches even though we were only replacing one switch. Then removed the two screws to the switch cover, and slide the cover up to expose the switches. He then took off one wire at a time from the old switch and replaced it one the appropriate place on the new switch. Exteremely easy repair and thank goodness because I (his wife) was the one who broke the switch. Thanks PartSelect!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 6 people found this instruction helpful

Parts Used

  • Infinite Switch

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsPliers

CustomerJohnny from Azle, TX

Burner would not work

changed out switch

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 21