2200550-1-S-Whirlpool-Y312959-Tumbler and Motor Belt
2200550-1-S-Whirlpool-Y312959-Tumbler and Motor Belt 2200550-2-S-Whirlpool-Y312959-Tumbler and Motor Belt 2200550-3-S-Whirlpool-Y312959-Tumbler and Motor Belt

Tumbler and Motor Belt

PartSelect Number PS2200550

At 100" in length, this dryer drum belt is 3/8" wide and has 5 ridges. This is the belt that is from the tumbler to the main drive motor.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not tumble.
  • Unusual Noise.
  • Takes too long to dry.
  • Will not start.
  • No heat or not enough heat.
  • Compare At

    $18.53
  • You Save

    $3.09
  • Your Price

    $15.44
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Drum Support Roller Kit

Part Number 1570070

This drum support roller includes one drum roller and two bearings. Most dryers use two drum rollers, and is recommended to change both at once.

$19.73
In Stock

Idler Pulley Wheel

Part Number 2347254

This part is used to help the belt to rotate the drum.

$11.09
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.0 / 5.0, 178 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerWilliam from Thomaston GA

Loud thumping noise while dryer was on

Unplugged dryer. Removed two screws and removed front of dryer disconnecting the wires from the front. Removed 4 screws and blue wire allowing the me to take the shroud off. Removed blower fan cover by taking out the screws and pulling down. Used pliers to take off clamp on blower fan and then had to use snap ring pliers to remove snap ring. Pulled blower fan off, replaced with new and put back on snap ring and clamp. Reinstalled blower cover, Removed drum by cutting belt (noted the direction of the belt around the idler pulley). Replaced belt (decided since I was going to be in the dryer and it is 14 years old I would replace belt as well) and drum. Reinstalled shroud and front cover. Dryer is very very quiet now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

Tools

CustomerKevin from Rineyville KY

Living overseas and caring for a dinosaur dryer

My friend Saeed did the repair (which was really maintenance) for me. What I really want to communicate is how WONDERFUL it is to use PartSelect for folks like us living overseas and keeping alive an ancient gas dryer (not available in Morocco and infinitely cheaper than electric). We don't have a local Maytag parts dealer, so we feel lucky to have this option of using the diagrams to order exactly what we need to keep our economical and efficient gas dryer going.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerJohnJohn from Trumbull CT

Loud noise

The actual promlem was the blower fan blade I also replaced the belt and other moving parts just because ! The only thing needed to do from the back is remove the 4 screws holding a metal plate on the lower right to gain access to the belt tensioner. EVERYTHING else is done from the front Don't learn the hard way (I did). Part Select was wonderful.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

Customerrobert from Malta NY

Replace dryer belt and rollers

Followed the directions which were included with the parts - this was a washer dryer combo and found it easier to remove the tension spring on the the idler roller assembly to set the belt in place and then re attach the spring to the frame body.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerSarah from Corrales NM

Loud noise

watch the video. drum roller failed(noise) but looking at the rest of the dryer I desided to replace belt(cracking) and front guides(worn through in places) also discovered it wasn't mice making nests in dryer it was stuff coming through where light protective lense should have been. The video is better instruction than I could give. Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerDave from Columbia Station OH

Loud rumbling noise

1st watched videos on making repairs on installing drum support roller kit,front glide kit and replacing tumbler belt.These repairs took approx 30 minutes but, didn't stop the rumbling. Went to a blog site that stated if these repairs didn't stop the noise I should take the tumbler belt off and see if the noise is coming from the motor area it was and further investigation revealed it was the plastic blower wheel,the flat spot on the blower shaft had worn out causing the blower wheel to rumble and vibrate. This repair took 15 minutes after watching the video on blower wheel repair. Runs better then new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerChris from MArietta GA

When the dryer grumbles check the blower wheel too.

If your dryer is making a rumbling noise, change the blower wheel. It's plastic and the heating and cooling cycles causes the keyway in the plastic to give out and the wheel just spins causing the noise and the slower dry time. The other parts I replaced see below. Like many other repairs, remove screws below dryer door. Mark all wires and locations for re-assembly. Next remove front tumbler/lint screen assembly (4 sheet metal screws 2/L 2/R. Work belt off back of tumbler and remove. Use flathead screw driver to release tabs that hold felts on both front and back tumble supports. Make sure you know rotation of tumbler and install new felts so the overlap goes in direction of spin. Use a drum stick or 3/8 ratchet extension, something dull and flat to press tabs back down on felts. A screwdriver could slip off and tear cloth. Next drill out heads of the rivets on the glides and remove teflon glide and cork backer. Make sure all rivet material is removed front and back. Install new cork and glide. Rivet one side back in, then the other. Repeat on 2nd glide. Re-assemble dryer. Super smooth, super quiet.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerMichael from Brighton MI

Dryer had been making a loud squealing noise then the drum stopped turning.

I wasn't sure how to access the belt inside so I went online looking for a diagram. I came accross the PartSelect website and found the awesome video instructions on how to disassemble, change each part and reassemble everything. I discovered I had a broken belt and the drum rollers were bad. I ordered the parts from PartSelect on a Wednesday and they arrived on that Friday. I started the repair on Saturday morning and following the video repair instructions a couple hours later my dryer was back in business for a very reasonable dollar amount. Thanks to PartSelect for making my repair so much easier!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)

CustomerRonald from Aliquippa PA

Noise coming from dryer and low air flow

Remove front panel, front drum support, remove belt, drum, blower cover, spring clip, blower cover, blower wheel assy.
Ordered new parts on line, came in two days, good service. Cleaned out all lint and installed new parts in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerGERALD from ALBUQUERQUE NM

Broken belt

Followed the instructions supplied with parts. My wife was so happy and the repairs were easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Tumbler and Motor Belt

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerJeffrey from Gloucester VA

Broken belt

Removed the front of the dryer and the vent assembly that held the drum in place. Removed the drum and cleaned the interior of the dryer with vaccum cleaner. I then oile the drum rollers which were starting to get dry and squeeky. Slipped new belt over drum and re-installed the drum vent assembly and then the fron of the dryer. Opened the rear access of the dryer and completed the installation oc the belt over the motor drive pully and idler wheel. Returned dryer to working location and tested - all was well. Note - the installation instruction that came with the belt are not clear on having to open the rear access panel. The directions made it sound like you can actually do everything from the front side - not likely unless you have 4 foot arms the size of broom sticks! Once I open the rear and could actually see the motor and idler pulley it was easy to finish.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerBrian from Palm Harbor FL

Drum bearing guides worn through - general rebuild

Removed two screws on bottom of front panel. Lifted bottom of front panel, it then it dropped down and was moved to the left side. Removed 4 socket screws and removed drum front cover. Replaced felt strip, removed belt and replaced. Replaced two idler pulleys in back. Removed blower housing front cover, removed blower wheel and replaced. Installed front drum glides after drilling out rivets from the old glides. Vacuumed entire inside thoroughly and reassembled.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Tumbler and Motor Belt

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerNorah from Philadelphia PA

Belt needed to be replaced

Previous entries about how to change the belt were very helpful. It's true; the instructions included with the replacement belt are very helpful and accurate. I decided to pull the tumbler out in order to be able to see the motor and pulley. I then read the directions a number of times so that I was sure I understood how to loop the belt around the motor, pulley and tumbler; knowing that I would need to put the tumbler back in and then "work blind" by feeling the loop of the belt and work it around the motor and pulley. To prepare for this, I taught myself how to loop the belt first by looking at the motor/pulley and referring to the instructions. Then, I tried it a number of times with my eyes closed, in anticipation of not being able to see what I was doing once the tumbler was back in place. When I was sure I could loop the belt with my eyes closed, I replaced the tumbler, slid the belt over the tumbler as instructed and reached back under the lower-left portion of the dryer to loop the belt around the motor and/pulley. I had it within a couple of tries. Note, it was imperative to pull up on the pulley to its maximum with my right hand in order to be able to complete the loop around the pulley with my left hand. Once I was sure I had the belt in place, I reassembled the front of the dryer and then took off the back access panel to spot-check the placement of the belt around the motor and pulley. I'd done it correctly. Additional note: while I had the tumbler out, I sprayed wd40 on the rotors since they have been sounding kind of "grindy". I wiped excess from the rubber surface of the rollers and surrounding areas. It worked like a charm and now the dryer is quieter than it has been since I inherited with the house I bought -4 years ago.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Tumbler and Motor Belt

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsSocket set

CustomerMarcella from Lake in the Hills IL

Broken tumbler belt

We had to take the tumbler out because we needed to see where the pulleys were. The directions for threadiing the belt around the idler pulley and motor pulley weren't clear. It took us quite a while to figure out that the belt had to be threaded back into the left side of the motor pulley after it was guided around the idler pulley. Once we figured that out, the directions made sense.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Tumbler and Motor Belt

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Socket set

Customerjose from miami FL

Broken belt

Removed the screws that hold the front panel, removed the two screws tha hold the top lid. Then removed the four front screws that hold the tub in place. Placed the belt around the tub 1.5 inches from the back screws on the tub where dark tracks from the old belt was showing. After that I secured the tub in place by mounting the front panel that holds the tub in place with the four screws. Then opened a small rear panel that has four screws and placed the belt around the motor as shown on the diagram where the belt came in. It was easier doing it from the rear where I could see the motor.

Help other customers find the most helpful instructions.

Were these instructions helpful?