2200270-1-M-Whirlpool-Y303836-Blower-Wheel-with-Clip.jpg
2200270-1-S-Whirlpool-Y303836-Blower-Wheel-with-Clip.jpg 2200270-2-S-Whirlpool-Y303836-Blower-Wheel-with-Clip.jpg

Blower Wheel with Clip

PartSelect Number PS2200270

This comes with a metallic hub clip to hold it firmly in place.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Takes too long to dry.
  • No heat or not enough heat.
  • Will not tumble.
  • Compare At

    $23.23
  • You Save

    $3.87
  • Your Price

    $19.36
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Blower Wheel Clamp

Part Number 600181

$2.70
In Stock

Tumbler and Motor Belt

Part Number 2200550

At 100" in length, this dryer drum belt is 3/8" wide and has 5 ridges. This is the belt that is from the tumbler to the main drive motor.

$18.86
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 141 reviews What's this?
 

0 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerSteven from Houston TX

Blower wheel spins freely on motor shaft

Removed front cover, Removed blower housing cover, Removed clamp holding fan to shaft. removed cir-clip from motor shaft,Replaced blower fan and reversed order of dissemble.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerDoug from Iola KS

Noisy clunky dryer

Thank God for YouTube. I watched a video that helped me identify the problem, then I watched another video of the part being replaced. **Unplug the appliance before you start. 220 volts is not a joke. Maytag dryers have changed very little in the past 40 years. I have a stackable washer/dryer pair with the dryer on top. I had to remove the front cover from the dryer, then remove the bulkhead that acts as a guide for the dryer drum. Next I had to remove the cover that runs from the lint-trap down to the blower motor. The problem was the shaft of the dryer motor is a D shape and the plastic squirell-cage fan (Blower Wheel) had worn to a full circle. So the squirrel-cage was just wobbleing around on the motor shaft. There were two spring clips to remove, then the blower wheel just pulled out. I put the new one on, replaced the clips, buttoned it all back up and plugged it back in. The result is a whisper quiet dryer. The hardest part of the whole process was removing the spring clips while trying to hold the drum in position (I was working alone).

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Socket set

Customerwilliam from port orchard AL

Rumble in dryer

remov door remove fan install new fan

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Socket set

CustomerMIldred from West Springfield MA

Drum would not turn

I FOLLOW THE VIDEO HOW TO CHANGE THE BLOWER WHEEL

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerRobert from Hainesport NJ

Loud deep rattling noise

Replaced fan on blower/drive motor. Fan became out of round and worn on shaft. Scotch tape was used to hold drive belt on tumbler. Also replaced belt drive wheel on opposite end of drive motor shaft.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers

CustomerJohn from east liverpool OH

Rattling noise

replaced tne blower wheel using instructions from Parts Select web site.Received the parts second day after I ordered them from Parts Select. Very pleased with results. Thanks for the help.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerBill from East Greenville PA

Dryer making noise

Our Maytag dryer was making a lot of noise..a rumbling that would continue for a few seconds after dryer would stop. Thanks to this web site, I determined it was the blower wheel. The plastic wheel "rounds out" over time, and slips on the shaft. Replacement was very easy...just keep track off all the screws and bolts you take off to access blower wheel...and make sure none of the wires from the front panel come undone. I saved myself a ton of money doing it myself...parts were abount 25$.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerMerlin S. from Clarkston WA

Blower wheel fell apart.

We also put a new belt and idler wheel on the machine, When you ave a soon who is a plumber, we had no problems, and thank you for prompt deliver of the parts..

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers

Customerlouis from locust valley NY

The blower wheel had cracked at the base

took the dryer apart, found the problem, and ordered the part. very quick shipping, we had it the next day. great!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerOscar L from Buena Park CA

Replaced blower..

Removed the 2 bottom screws under the front cover. Lift up and you could set it aside. Remove all the blower screws using a nut driver. Here you, you will see the blower and remove the lock ring using a ring pliers and the clip using a needle nose pliers. Remove the old blower and install the new one, make sure the flat side of the shaft matches with the blower. Put back in reverse order all you remove..

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerDale from Mentor OH

Very noisy

I just followed the video to the letter or recording

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerGeorge from Key West FL

My wife, the dear little thing, heard a clunking noise when she turned on the dryer.

I am a builder and a fixer, but have never fooled around with washers and dryers. They just seemed too big and complicated and specialized. But for some reason this time I went to a Maytag parts site, ended up with Parts Select, and happened across the question of what was my problem. The loud noise answer showed most likely causes of noise, so I ordered the two parts with the the best chance to be the culprit. Then I found the video with the nice guy doing the job slowly and clearly, and it looked like a snap. It was sort of like the old Volkswagon Bug "Repairs for Idiots Book" or whatever it was called: "First, open the hood. Second, prop up the hood with a stick so it won't fall down on you. Third . . . ." Received the parts in the mail, pretty reasonable, looked at the video a second time, and opened 'er up. I was amazed at all the space in there, and how simple everything was. Wiggled and spun the rollers, then spun the fan and there it was - the grinding noise. So I replaced the fan, put it back together and the problem was solved. Later I had to put in a new belt too, so I recommend doing that any time you take out a major part in an old dryer. My old belt was sorta cracked and I should have replaced it along with the fan but I thought it would keep on working. Stupid me. But the whole program was just right for someone with an hour or two who wants to save that $150 repair bill from an appliance repair guy who comes to your home and does the exact same thing you can do yourself. Just LOVE the probability percentage list of which part is bad, and the videos on how to do the work. I'll use this system again, if needed. George

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerLawrence from Sunnyvale CA

Dryer made a loud rumbling and chattering noise.

Followed excellent instructions. Removed front panel of dryer and removed front bulkhead to get to the blower assembly. Removed the cover on the blower assy and saw that blower was damaged and loose on the shaft. Using snap ring pliers, removed the snap ring, then using ordinary pliers, removed the clip spring that holds blower tight on the shaft. Replaced blower and reassembled. This was probably the problem. However, since I'd ordered the drum support rollers, I replaced those, too. To do so, used rear access panel to take belt off idler pulley (to relieve the tension) then removed drum. Using snap ring pliers I removed the old rollers, replaced with the new and reassembled. The roller shafts looked fine, so I didn't replace. Reassembly of the drum and belt required an additional set of hands, so I called a friend. Note: it helps a lot to remove the two screws holding the top of the dryer in place. Then you can swivel it a bit to allow access to the top of the drum--helpful in getting the belt back on correctly. Whole job took maybe 1-1 1/2 hours. Dryer works like a charm! (Incidentally, the parts arrived within a day or two of my placing the order, and I didn't opt for the expensive shipping!)

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyEasy

Time to do repair:30 - 60 mins

Tools

CustomerCraig from Falcon Heights MN

The dryer was really loud when in use.

I replaced the drum rollers and guide pads, and the blower. Now everything works like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerAustin from Cupertino CA

Rumbling / groaning noise when dryer starts

I thought the noise was coming from the rear belt / pulley system, but found it was from the front blower wheel.

First phase: disassemble to figure out problem -- found the front glides were worn and tumbler belt was old & cracked and noise was from blower wheel. Vacuumed out tons of lint. Ordered parts. Had to order rivet tool & ring pliers (tools cost $25 including shipping). One hour.

Final phase: Disassemble & drill out glide rivets -- attach with new rivets (easy). Replaced blower wheel & belt (easy). One hour.

Runs great -- no noise. Cleaning helped drying ability. Videos were key. ALWAYS REMEMBER TO UNPLUG! I didn't & nearly welded my fingers to the chassis.

Help other customers find the most helpful instructions.

Were these instructions helpful?