2194879-1-S-Whirlpool-Y0316773-Spark Ignition Electrode
2194879-1-S-Whirlpool-Y0316773-Spark Ignition Electrode 2194879-2-S-Whirlpool-Y0316773-Spark Ignition Electrode 2194879-3-S-Whirlpool-Y0316773-Spark Ignition Electrode

Spark Ignition Electrode

PartSelect Number PS2194879

Sold Individually.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not start.
  • Gas igniter glows but will not light.
  • Cooktop element not heating.
  • Compare At

    $17.34
  • You Save

    $2.89
  • Your Price

    $14.45
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 11 reviews What's this?
1-11 of 11
 

30 of 37 people found this instruction helpful

Parts Used

  • Spark Ignition Electrode

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerHUY from ALISO VIEJO CA

Broken electrode, no spark

Remove 2 screws holding the top burner. Remove 1 screw holding the electrode. Remove electrode from wiring using plier. Install new electrode and top burner

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 12 people found this instruction helpful

Parts Used

  • Spark Ignition Electrode

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMichael from Friendswood TX

Burner would not ignite when control in "light" position

Remove the two screws from the burner assembly (on top of the burner). Lift burner assembly from the cook top. Disconnect the electrode wire from the electrode. Remove the screw holding the electrode to the burner assembly (on bottom of burner). Install the new electrode and attach the electrode to the burner assembly. Attach the electrode wire to the electrode. drop the burner assembly back into position on the cooktop. Attach the burner assembly using two screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerD, from Imbler OR

Gas burner wouldn't ignite. No spark

Replaced the spark igniter which had been broken.
Great response and shipping time, even though one part was back ordered. Works perfectly!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerpeter from metairie LA

Onlly 1 burner working

removed 2 screws on each burner and disconnened wire . replaced module so the top of range had to be lifted. Shut powder to unit. removed wires one at atime and connected to the new module, then reinstalled wires and screws to burners. very simple task

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Spark Ignition Electrode

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers

Customercharles from hillsboro OR

None of the burners would light

I removed all 4 burners 2 screws holding each,replaced the ignition module,wire for wire,reassembled after cleaning the stovetop.I,m my wife's hero.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Spark Ignition Electrode

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerWayne from Woodstock IL

Replace ignition electrode gas range

Wow, ordered the part here and it arrived in 18 hours!! Job was fairly straight forward but the screw holding it in place was corroded and stuck. Several heating and cooling cycles with a torch and some spray lube and lots of patience and I finally rocked the screw lose.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Spark Ignition Electrode

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerGary from Glenwood Springs CO

Ignition electrode broke

Removed the two screws that hold the element in place. Disconnected the wire to the electrode. The screw holding the electrode to the burner plate would not unscrew so I had to drill out the screw in order to replace it with the new ignition electrode. A little more time involved but if the screw would have come out it would have been a 10 minute job.When I ordered the part from you it came very quickly and I will certainly use you again when I have any other issues.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Spark Ignition Electrode

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerRobert from Philadelphia PA

Cracked ignitors (2)

No problem removing the burners. Removing the old initors was a different story. The tiny screws that hold the ignitor in place were baked in and could not be removed with a screw driver. I drilled them and tried to use an easy out to no avail. The screws are very short so I had to use care not to drill thru the burner. Both screw heads did snap off. I resorted to a hi temp epoxy to secure the ignitor flanges to the burner and now the all burners ignite as designed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Spark Ignition Electrode

Level of DifficultyDifficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Wrench set

CustomerStanley from St. Louis MO

The spark was no longer igniting the burner

The earlier reviews said very easy and 15 minutes for beginners. They were right on, except I could not get the old screw out no matter what I tried. I eventually had to drill it out and put in a self tapping new screw. This was a first for me. Then it took 15 minutes or less and works fine again. Hopefully next time someone will tell me how to get that old screw out faster.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Spark Ignition Electrode

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerTimothy from Naperville IL

Range would not lite

diagram on website was very helpful. simply unscrew two screws,remove and replace electrode and works perfectly.
Ordered one day arrived next with standard shipping installed before next day supper awesome service

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Spark Ignition Electrode

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerEmily from Silver Spring MD

Ignition no longer work

It was really easy because I read information on your site. I only had to unscrew 3 screws, remove the old spark ignition electrode, replace the new one and then screw the 3 screws back. It was great

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-11 of 11