Defrost Heater and Thermostat Assembly

PartSelect Number PS2061407

The heater is located beneath the coils that are located behind the panel in the freezer section. The heater will get hot and melt any ice or frost build up around the coils. The thermostat will sense the temperature increase in the evaporator during the defrost cycle and will cycle the defrost heater off after the ice or frost is melted.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Fridge too warm.
  • Freezer section too warm.
  • Freezer not defrosting.
  • Compare At

    $54.19
  • You Save

    $9.03
  • Your Price

    $45.16
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 10 reviews What's this?
1-5 of 10
 

15 of 17 people found this instruction helpful

Parts Used

  • Defrost Heater and Thermostat Assembly

Level of DifficultyReally Easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerMark from Manhattan, KS

Freezer/refrigerator not cooling

Turn off freezer.
Pull the shelves out of freezer.
Remove two screws that hold on back panel.
Melt ice off of cooling fins with hair dryer.
Remove heating element by unplugging heating element on top of fins, pull off wiring with small unit clipped to tubing, slide the wires out from the side of the fins, and pull off clip on the bottom of the cooling fins that holds heating element.
To install new part I just reversed these steps.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Defrost Heater and Thermostat Assembly

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Socket set

Customermichael from virginia beach, VA

The back wall of the freezer kept icing up, wouldn't defrost

1st, I removed all the shelves and baskets. 2nd, I removed two screws (1/4" nut driver/socket) that attach the two lower panels at the back of the freezer. If there frozen on defrost with a hair dryer, with panels removed finish defrosting the coils and the two vents (top and bottom) on the inner wall. With the coils defrosted unplug the unplug the defrost heating element then remove the two screws securing the coil to the back wall of freezer. Coil movement is limited so be gentle. remove the retaining clip at bottom of coil. remove the element starting from the top, work it around the foam insert (dont remove the foam insert). install in the reverse order and dont forget to clip on the thermostat.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Defrost Heater and Thermostat Assembly

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJOHNNY from BRYANT, AR

Kept freezing up after a couple of months

replaced the defrost heater assembly and it solved the rpoblem

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Defrost Heater and Thermostat Assembly

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerGIAU from HILLSBORO, OR

Ice build up,coverd coil .

Disconnected power,removed 2 screw on penel covered the coil,took off 2 penels that cover the coil.Use heater to melt ice.Removed & replaced new defrost heater & thermostat.So simple.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Defrost Heater and Thermostat Assembly

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerDavid from Effingham, IL

Freezer not cold enought and refrige not cold at all

I just recently replaced my defrost assemby which is very easy to do and the unit defrosted a few times then the condenser froze up again. I replaced the Heater/therm assy and it's been working well and defrosting properly now for a week. Hardest part of install is getting the plastic shroud off, you have to pull our and push down at some time, the back two clips are a bit of a pain but will eventually come down. After that it's a few screws and the unit falls out and is very simple to replace.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 10