2039613-1-S-Whirlpool-37001298-Drum Glide
2039613-1-S-Whirlpool-37001298-Drum Glide 2039613-2-S-Whirlpool-37001298-Drum Glide http://www.partselect.com/Schematics/Maytag/58910.gif

Drum Glide

PartSelect Number PS2039613

This drum glide is sold individually. ***Please Note: these should be replaced in pairs.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Noisy.
  • Will not tumble.
  • Marks left on clothes.
  • Compare At

    $8.38
  • You Save

    $1.40
  • Your Price

    $6.98
On Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Single Felt Pad

Part Number 2045752

Sold individually.

$3.91
On Order

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 43 reviews What's this?
 

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Socket set, Wrench set
Customer: Alan from Great falls, MT

Grinding noise from dryer, clothes caught around drum

Removed bottom front panel by two screws. glide brackets at about 8 and 4 o'clock positions, with screws coming in from the back. The replacement glide bracket and two drum glide will be needed. I drilled out the screw holes and used the original screws because replacement screws were too short and the screws go in from the front on the replacement glide bracket. You will need to slightly raise the front of the drum to install the glide brackets correctly. the reinstall the front cover.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers, Socket set, Wrench set
Customer: Thomas from Naugatuck, CT

Loud squeking noise as drum turned

I was somewhat intimidated by the fact that dryers are all repaired from the front. Pulling out the drum seemed scary at first, but that turned out to be very easy. After removing the front panel and lint shroud it is easy to reach the idler pulley and take the tension off the belt. If you're going to replace the rollers which is generally the cause of the noise, get new retaining wrings and a decent pair of pliers for them. The rings can lose all their spring easily by strechting them too far to get them off. Replace the idler pulley and belt while you have the dryer apart. Vacuum all the lint out of there and you're good to go.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Socket set, Wrench set
Customer: Richard L from Eatonton, GA

Glides were wore out and pully was gone.

Replaced glides and assy idler pulley cleaned all parts fron dust and debree, vaciumed heating eliment to remove all excess lint and wool to make sure I did'nt have a fire in the lower unit.
Job was'nt all that hard just have to watch what you're doing.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: Rick from Marlborough, MA

Noise and heat will not stay on (gas dryer)

Parts that were recommended for the noise issue were spot on. Instructions were very helpful and made the job go very smooth. Replaced the belt, rollers don't forget to order (2) felt pad and idler pulley replaced.
The part suggestions for the heat problem did not fix the problem. The burner flame would come on for 2-5 min. then go off. A few min. later the burner would try to ignite but would not start. The igniter would get cherry red but no activation. I end up replacing the coil kit. Turned off the gas removed (2) screws and wala done 5 min. and it fixed the problem.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Robert from Averill Park, NY

Heard the sound of loose change in the dryer

removed the front panel and the drum panel cover.replaced the guides and the felt pads and re-assembled.

Help other customers find the most helpful instructions.

Were these instructions helpful?