2017676-1-S-Whirlpool-21001108-Motor Pulley
2017676-1-S-Whirlpool-21001108-Motor Pulley 2017676-2-S-Whirlpool-21001108-Motor Pulley 2017676-3-S-Whirlpool-21001108-Motor Pulley http://www.partselect.com/Schematics/Maytag/35874.gif

Motor Pulley

PartSelect Number PS2017676

This part may differ in appearance, but functions same as original part.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Burning smell.
  • Will not drain.
  • Will not agitate.
  • Pumps but will not spin.
  • Noisy.
  • Compare At

    $15.44
  • You Save

    $2.57
  • Your Price

    $12.87
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 17 reviews What's this?
 

10 of 16 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Screw drivers, Socket set
Customer: Dale from Thompson, ND

Overloading, and general abuse of the machine had caused the motor and spin pulleys to burn and the belt to slip. (pungent burn odor)

I used a small screw driver to remove the teeth from the motor pully and fit the puller on the pulley with a small socket protecting the end of the shaft. it came off easily with a few turns on the puller. I placed the new motor pulley on the shaft and tapped it into place with a small dead-blow mallet (a hammer with a hollow, heavy, plastic head filled with sand). Unfortunately, the spin /transmission shaft pulley was an incorrect part for the application and the motor turned out to have some internal heat damage. I was not able to apply this part because it was the wrong application but if it is you are in luck. The clip removal is the same and install this pulley flat side down and reassemble. If not, read on. I removed the motor by removing the front panel, removing the three bolts securing the motor to the plate, and disconnecting the wiring plugs and ground wire. I lucked out finding a spin pulley and motor rebuild kit locally. After rebuilding the motor with the new bushings, brushes, etc. from the kit, I reinstalled it by reversing the removal steps. I then removed the spin/trans pulley by removing a plastic grease cup/cover from the end shaft and removed the C-clip and washer holding the pulley in place with a small screw driver. I was careful not to let the pulley and washer/thrust washer stack on top of it fall off so I could be sure of the order in which they should be reinstalled. I applied fresh grease and reversed the disassembly proceedure making sure to drive the C-clip fully into the slot on the shaft with a large flat-tip screwdriver and the mallet. I cleaned, regreased, and reinstalled the grease cup/cover back into place firmly making sure it snapped into place. I slipped the belt back on the pulleys and reinstalled the front panel with the two screws at the top inside corners. The job was done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: charles from nicholasville, KY

Pulley was broke

took hammer,screwdriver,cut old one off then took the newone and aline it up on spline put socket over it drove it on.a little at a time untell the lock on the end whent in the groove. done thank you. ps you dont have to buy a motor with pully.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used:
  • Motor Pulley
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Socket set
Customer: Anthony from Bryceville, FL

Motor pully broke

First our local store said you had to buy the whole motor. I didn't. I bought the pully from you guys and took pliers and pulled the broke pully off and put a socket on there and hit it with a hammer and then she washes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used:
  • Motor Pulley
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools:
Customer: David from Haverhill, MA

Drive pulley split in half after installing new belt

I used two pry bars to evenly and gently remove old pulley then I gently hammered new one in place and reinstalled belt.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 9 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Clarence from Crosby, TX

Pully was broken, belt worn in one spot

Remove screws holding backplate, reomved backplate. removed belt and pully, replaced pully, replaced new belt, returned backplate and screws. worked great

Help other customers find the most helpful instructions.

Were these instructions helpful?