Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11752991
Note: As per manufacture a new screw is needed to mount door cam.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
First I removed all contents from inside refrigerator door.Then I removed (1) 10mil screw,which holds cover for top hinge.Next I removed the (3) hinge screws,and lifted door off of bottom hinge.Pulled off plastic closure cam from bottom metal hinge post.I cleaned metal post ,applied a small amount of vaseline to post, slid on new plastic cam,installed door, replaced screws.Very easy,10 to 15 min tops.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Super-easy... First, empty refrigerator door. Then, just remove the bolt that goes through the cover over the top hinge. This exposes three more small bolts. Remove these and the top hinge assembly will lift off. Lift door off. Remove cam from door and lower hinge, slip new cams on, and reassemble. The hardest part was pulling all of the junk stuff out of the refrigerator door. Who know you could accumulate so much salad dressing?
1. Put pieces of wood under door to support it.2. Unscrew three screws holding door hinge.3. Disconnect water line.4. Unscrew screw holding each cam. One to door and one to hinge.5 Replace cams.6. Retrieve plate with threaded holes behind frame that the hinge attaches to.7. Use thin philips screwdriver through the hinge bracket, shim, frame and screw plate to align it for the other two screws.8. Replace all three hinge screws.9. Connect water line fitting.10. Remove wood for door support.11. Check door for smooth movement and strong pressure when closed.
I did some tests and determined that the tub-to-pump drain hose had a leak in it.I then looked on the web to find disassembly instructions. I have a stacked washer dryer combination in a very confined space. The repair involved disconnecting both the washer and dryer from the water, gas, electric and venting systems first, then unstacking the dryer from the washer (not so easy, it required a helper). The machine was then pulled out so I could get at the parts necessary to remove the outside components and sheet metal. Then, I disassembled the top, front and access panel in the back. The disassembly went very well. I got access to the drain hose assembly and removed it fairly easily. I ordered a replacement drain hose assembly and found that installing the large port of the assembly was very difficult. (The two other ports were easy.) After thinking about it, I tilted the machine back a bit so I could try it from the bottom. That worked fine.I then reassembled and tested the machine. No leaks. Good luck with yours!
This was a very simple job. Remove the top Hinge bracket, a total of 4 screws, lifted the door off the bottom hinge, removed the bottom hinge set up, 2 screws, replaced it, and attached the new bottom black door cam, lifted the door back onto the bottom hinge and aligned the top hinge, and reinserted the screws, and Ta Da, The door works like a new refrigerator door. 15 to 30 min tops. I did not even have to take the refrigerator items out of there door holder.
Simply remove the cover over top hinge and remove the three outer screws (Do NOT remove the center screw). Lift the door off the lower pivot pin. Turn door upside down and replace the upper cam and then the lower cam on the pivot at the bottom of the refrigerator case. Reintall the door by setting the door on the lower pivot and then reinstall the top pivot and cover. VERY easy and what a difference. No more "POP".
Purchased the closing cam (both pieces). Removed door (3 bolts under the dust shield on top of door) and replaced the plastic cam pieces. So easy a caveman could do it. I actually had my 13 year old son do it while I supervised!
removed screw on top cover emptied ref door remove 3 top screws holding bracket on top. lifted the door then remove old cam then reassembled.
Undo a few screws on top of door, replace closing washers at bottom part of door, put door back on, and done. Easy. Just make sure you have the top and bottom closer washers that go together...2 parts.
Remove replace door with new cams.
Turn fridge off. Removed top hinge cover. Removed three screws in top hinge. Lifted hinge from door. Lifted door off bottom hinge. Place door on level surface and removed old cam with socket set. Installed new cam. Removed old cam from bottom hinge with socket set. Installed new cam. Cleaned bottom of door while had easy access. Placed door back on bottom hinge. Install top hinge and screws. Finished.
Removed the top hinge cap. Removed the 3 screws with a nutdriver. Lifted the door off of the bottom hinge and placed it on it's side. Then I removed both closing cams (one screw holding each). Clean the area then replaced each cam. I put some vaseline on the bottom cam and replaced the door. 4-5 minutes not counting removing and replacing the food inside the door shelves. I'm 56 years old and have always done most of my own handywork. I don't remember any job going so smooth and fast! Ever!
easy - remove the door, replace th part, put back the door
Removed right hand door of side by side. Replaced both cams and put door back. All is well.
We thought we were in need of a new seal around the door but as my husband checked the door he found out it was a piece under the door that holds it up so the door was not sealing right when it closed. I went on line. Found this site and found my fridge. My husband viewed the pics of the parts and figured out we needed a cam. I ordered my part and could not believe it came the very next day!!! I didn't even pay for anything other then regular delivery. He took off the door and it was simple to just slip on the new part and replace and put the door back on.. Nothing much to tell here. Less then 30 minutes. Thank you so much for the quick service getting it out to us. I was about to put a child lock on the door just to keep it closed..
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.