Models > 10641014100

10641014100 Kenmore Refrigerator - Overview

Get Parts and Repair Help for 10641014100

If you know the refrigerator repair part you need, you can browse the list of all parts on the 10641014100, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for 10641014100 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.82

Light Bulb - 40W

Sold individually.

$3.96

Lower Door Closing Cam

This door closing cam is located on the bottom of the fridge/freezer.

$53.86

Meat Pan with Handle

$20.44

Defrost Timer Kit

This eight-hour defrost timer will replace most other defrost timers. This device acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater. The best way to make sure you get the correct timer for your refrigerator is to conduct a search for your model number.

$59.46

Thermostat Assembly

The thermostat will sense the temperature increase in the evaporator during the defrost cycle and will cycle the defrost heater off after the ice or frost is melted.

$4.11

Door Cam

$2.70

Screw

This screw is sold individually.

$31.33

Bi-Metal Defrost Thermostat

If ice is building up in your freezer or if your freezer is getting too warm on the defrost cycle you may need to replace the bi-metal thermostat.

$7.28

Light Rocker Switch

$51.55

Compressor Start Device Kit

This kit has been redesigned and the wiring may be different than the original. It will possibly need to be installed by an appliance repair person.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Clicking from underneath the fridge, and compressor engaging only intermittently

  • Customer: Michael from Manvel TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 150 of 183 people found this instruction helpful
I diagnosed the problem as a bad relay. I detached the two sets of wires leading to the relay and compressor, then pulled the relay off the compressor. It rattled and small bits of detritus fell out from inside of the relay. The new relay came the next day. It did not rattle. It was identical and I simply did the reverse to reinstall. read more

inconsistent compressor and condensor fan operation

  • Customer: Steve earney from Brooks GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 97 of 99 people found this instruction helpful
Compressor start relay would cycle several times before compressor would come on. Replaced start relay and defrost timer assy. Operated more consistently however not completely reliable. Ice would begin to melt. Noticed that if you would cycle the temperature control the compressor would start again and operate for several hours then not cycle again. Jum... read more

Both freezer and refrigerator stopped cooling

  • Customer: Laune from Front Worth TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 98 of 116 people found this instruction helpful
Compressor Start Divice kit, I took off back lower panel with the 1/4 inch nut driver, on the compressor their was a wire hook that held the starter in place used my plyers to unhook, pulled the unit off plug the new unit in reappled the clip it was so easy I had to exame it severl to time to make sure that was all their was to it. put the cover back on and ... read more