Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11752991
Note: As per manufacture a new screw is needed to mount door cam.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
The design of this refrigerator door (it's a side-by-side) is somewhat unbelievable. The door is designed to hold things, yet when you do the weight of the door wears out the lower door cams. The cams are designed to "complete the door closing", i.e. when you gently push on the door the cam mechanism takes over. When the cams wear, the door fails to close. Note to others - you may mistakenly think that the failure of the door to close is related to the seal; it is not.The repair is quite easy; remove the upper cover, using a not driver (socket), then remove the upper door bracket. Make sure you hold the door or have someone else hold it. After the fasteners are removed gently lift up on the door and remove it from the lower cam assembly. You will see two plastic cam pieces; one on the lower bracket and one on the door. Both need to be changed to effectively "renew" the door closing mechanism. Once the cams are replaced the door can be reassembled to the refrigerator.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Super-easy... First, empty refrigerator door. Then, just remove the bolt that goes through the cover over the top hinge. This exposes three more small bolts. Remove these and the top hinge assembly will lift off. Lift door off. Remove cam from door and lower hinge, slip new cams on, and reassemble. The hardest part was pulling all of the junk stuff out of the refrigerator door. Who know you could accumulate so much salad dressing?
1. Put pieces of wood under door to support it.2. Unscrew three screws holding door hinge.3. Disconnect water line.4. Unscrew screw holding each cam. One to door and one to hinge.5 Replace cams.6. Retrieve plate with threaded holes behind frame that the hinge attaches to.7. Use thin philips screwdriver through the hinge bracket, shim, frame and screw plate to align it for the other two screws.8. Replace all three hinge screws.9. Connect water line fitting.10. Remove wood for door support.11. Check door for smooth movement and strong pressure when closed.
Simply remove the cover over top hinge and remove the three outer screws (Do NOT remove the center screw). Lift the door off the lower pivot pin. Turn door upside down and replace the upper cam and then the lower cam on the pivot at the bottom of the refrigerator case. Reintall the door by setting the door on the lower pivot and then reinstall the top pivot and cover. VERY easy and what a difference. No more "POP".
Purchased the closing cam (both pieces). Removed door (3 bolts under the dust shield on top of door) and replaced the plastic cam pieces. So easy a caveman could do it. I actually had my 13 year old son do it while I supervised!
Removed the top hinge cap. Removed the 3 screws with a nutdriver. Lifted the door off of the bottom hinge and placed it on it's side. Then I removed both closing cams (one screw holding each). Clean the area then replaced each cam. I put some vaseline on the bottom cam and replaced the door. 4-5 minutes not counting removing and replacing the food inside the door shelves. I'm 56 years old and have always done most of my own handywork. I don't remember any job going so smooth and fast! Ever!
easy - remove the door, replace th part, put back the door
Removed right hand door of side by side. Replaced both cams and put door back. All is well.
We thought we were in need of a new seal around the door but as my husband checked the door he found out it was a piece under the door that holds it up so the door was not sealing right when it closed. I went on line. Found this site and found my fridge. My husband viewed the pics of the parts and figured out we needed a cam. I ordered my part and could not believe it came the very next day!!! I didn't even pay for anything other then regular delivery. He took off the door and it was simple to just slip on the new part and replace and put the door back on.. Nothing much to tell here. Less then 30 minutes. Thank you so much for the quick service getting it out to us. I was about to put a child lock on the door just to keep it closed..
supported the door on blocks. removed old parts with a socket and ratchet. the new parts didn't line up quite right, so some modification with a dremel was necessary. otherwise, the repair was very simple.
pulled top hinge pin off with 5/16 nut driver ,lifted door off and was able to see both parts and replaced them just like they were,easy fix
Removed all the adjustable shelves inside the door. Removed the top hinge cover (1 nut). then the top hinge bracket (3 nuts). The door doesn't weight very much so you shouldn't have to worry about the door just falling off after you remove the top hinge. then simply lift the door off the bottom hinge and carefully lay it down. One nut in each of the plastc cams on the bottom of the door and an easy swap out with the new parts. A little vaseline one at least one of the surfaces of the cam, reverse the order and simply put things back together and your good to go. Door closes on its own like new. You might as well get both parts for the lower cam and swap them out simultaniously since you have the door off. PLEAS NOTE: Yes there are two different parts for this repair.
Part arrived overnight. The How-To video at PartSelect showed the procedure exactly. It took about 30 minutes.
pulled all shelves from refrigerator door. unscrew the top plate and lift door out of bottom. pulled old cams off the door and the lower bracket and installed the new cams. put door back on and screwed the top bracket back on. installed the door shelves back in the door. never took the food off the door shelves. easy, easy, easy.
We dealt with this problem for well over six months. Last week while visiting our home my mother tried to schedule a repair man to come out. Upon hearing this conversation i urged her to hang up the phone and let me fix it. This prompted me to go on line and find the three dollar part needed to fix it. With the help of a friend to lift and hold the door i unbolted the black closer piece and replaced it with the new one. This whole process took less than 10 minutes and completely fixed the problem. The service visit would have cost upwards of $80.00 so this was well worth the two days shipping i paid for.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.