Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11750107
This eight inch chrome drip bowl is intended for use with many electric ranges and cooktops.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
So often we feel inclined to contact repairmen for simple jobs. This was easy because I ordered the part by looking on the side of the range. It arrived in less than a week. I simply snap the bowls inside the correct sockets and now my stove looks new. I definitely would use this service again.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Took out the old drip bowls and replaced with new bowls.
I removed the element and then the drain pan and replaced with the new correct pans. I replaced the element and all was well.
I just put the drip bowl in and plugged in the new heating element and I was done. It heats much faster and is level now so cooking is much easier. Also the parts arrived sooner than I expected, so I was very satisfied overall. Couldn't have been much easier all around. I will use Partselect.com in the future. Thanks
just move one wire at a time. Each switch has 5 wires and I am sure mixing them would not be good.Ordered parts, they shipped same day. Arrived exactly as predicted. Totally non-stress. Can't find a thing to complain about.Thanks PartSelect
Turn the power off to the unit. Remove the cold element by lifting up and pulling out. Remove the drip pan. Remove the element plug screw and pull the plug up and out of the socket. Cut the leads to the plug as close to the plug end as possible to allow enough wire to splice the new plug in. Strip the insullation back 3/8" to allow for splicing. Install the shrink tube collar on the wire and place one new lead (prestripped at the factory)next to the old wire and place the wire nut provided over the bare wire ends and twist it on until it is tight. Bend the wire nut splice back over one of the leads and slide the shrink tape over it. Heat up the shrink tape with a hair dryer to make it tight over the wire nut connection. Repeat the process for the next lead. Slide the leads into the new socket. Install the socket and secure the the new screw provided. Reinstall the drip pan and plug in the heat element. Follow the same procedure for each element socket replaced. Turn the power back on.
replaced drip pans with correct type
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!
This wasn't a "repair", but I got an email asking for my story, so here it is. :-)I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
To replace a bowl lift burner slightly (1") then pull gently until it comes out. Remove bowl, replace with new bowl. Insert burner by pushing gently yet firmly, place down into clip.To replace indicator light, remove panel from back of stove.Locate light indicator switch, push indicator lens through front of stove, hold in place (may require a second person) slide switch unto the nub of plastic on the indicator switch. Repeat for each broken indicator lens.
took out the old ones and replaced them following the instructions provided by you. thanks
More Than Amazing! I found you by searching google and using the make/model of my stove. The photos were so helpful, it made ordering a breeze. The parts arrived as if by magic! (within 2 days). I do a lot of online ordering from different stores and all I can say is that your service was above all of them. I use my stove daily. Not only that, the new parts made my stove look brand new. P.s. I never respond to survey's unless they deserve it.
This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.
Unwrapped package. That was the hardest part. Inserted into the little spot on top of stove. Tested. Worked great!
removed the heating element then removed the screw that holds the plug in on cut the two wires and reconnect the two wires and put back
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.