Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11749915
This ice cube mold and heater assembly has a flake resistant surface. It is used with modular style icemakers on some refrigerators.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Remove the ice maker with two screws in the side and one screw in the bottom. You don't have to completely remove the side screws but you do have to remove the bottom screw.Lift up on the ice maker and reach behind it and unplug the wiring harness. The tube that lets the water in is accessible from the rear of the fridge. Remone the water line, its only finger tight, and remove the two screws. Pull the tube up and out. Thaw it out with hot water and reinstall. With the ice maker out and on the table, pop off the front cover. Remove two phillips head screws and slide the cube tray off. watch how everything is placed before you slide it off. Slide on the new tray and reinstall all screws. Reassemble in reverse order that you took it out. Your ready to make ice...
Help other customers find the most helpful instructions.
Were these instructions helpful?
My ice maker just stopped filling with water one day and after some troubleshooting, I found that a chunk of ice had built up in the tube between the water supply line and freezer. I took the ice maker out (Don't touch the heating element...it really hurts) and defrosted the ice obstruction by injecting hot water into the tube to melt the ice. I used a new plastic syringe you get with an infant over the counter drug and a bucket to catch the water. I noticed the ice cube mold was peeling and decided to replace the mold. The mold is an easy replacement as long as you remember how you took it apart. My mold had some glue or compound stuck to the side that kept me from getting the mold flush against the motor assembly housing so I had to uncrew and scrape that gunk off and reattached. Other than that, there was nothing to it. Now the ice maker is good for another 8 years.
Removing the ice making assembly from the Ice compartment was not difficult except that two of the 3 screws we not visible without a mirror and then my nut driver was 5" long making it very tight quarters, so it was a time consuming process to remove them.Once the 3 screws were removed the wiring harness was easily disconnected and the whole assembly came out.The next step was to figure out how to remove the faulty part from the rest of the assembly. After some strong persuasion the part would not separate from the control Assy. (The front of the unit) To complete the job I had to pull the front cover and unplug the motor and heater assy to expose two additional screws that had to be removed to pull the defective part out. The reassembly went quite easy except the 2 screws that you need a mirror to see. I was also trying to hurry because the frozen items were not holding all that well after the door was open for about an hour and a half. An instruction sheet showing the steps would have cut the time over 1/2!
Removal of the Ice Maker required the removal of only one screw from underneath the maker and the power connector disconnect. Dis-assembly was straight forward. Remove old tray and heater, and reassemble with new tray and heater unit. Reinstall Ice Maker! Special Note: Allow the Ice Maker time to cycle through it's sequences. It may take a period of time before it starts producing ice after re-installation.
turned water off to ice maker unpluged fridg while doing repair which was such short time everything was ok removed 3 1/4 hex screws holding ice maker in position while holding ice maker in hand unpluged wiring connection for it removed old ice mold which coating had come off of which was very simple 2 philips screws which are recessed on control unit then gently wiggle assembly apart paying attention to how all the tray parts went together then reinstalling same way as they were remove very simple repair anyone should be able to do
I removed the ice maker, saw the problem, took the ice maker apart and ordered a new mold. I reassembled it with the new mold and it now makes ice but the control arm remains up after each ice dump. I plan to take the ice maker back out when we leave (we are snow birds in Florida) and see if the arm is properly placed.
Removed icemaker found ice mold protective layer coming off. Replaced ice mold and working great. Online graphic very detailed and easy to determine part needed. Easy and great delivery. Highly recommended for future repairs.
Loosen to screws under ice mold and unplug power cord from icemaker.Lift out complete unit. Remove cover on ice maker,then 3 screws on end plate and remove end plate. Remove 2 screws that hold ice mold to frame. Make sure that the thermostat is moved to new mold. Reverse order to install new mold.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.