Models > 10644029602

10644029602 Kenmore Refrigerator - Overview

Get Parts and Repair Help for 10644029602

If you know the refrigerator repair part you need, you can browse the list of all parts on the 10644029602, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for 10644029602 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$70.13

Water Filter

This Whirlpool filter reduces taste and odor of clorine, small particulates, benzene, toxaphene, lead and mercury. It pushes in the botton front grille. Suggested replacement is ev...

$2.58

Light Bulb - 40W

Sold individually.

$112.25

Ice Maker Assembly - 8 Cube

This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and...

$18.59

Water Filter Cap

Black in color.

$66.61

Icemaker Control Assembly

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.

$22.61

Dispenser Grille

This grille is located on the bottom of the ice/water dispenser to catch the overflow.

$50.65

Ice Door Kit

This kit includes the ice door, support, spring and delay. The heater ribbon is no longer attached - the heater is no longer needed.

$24.19

Bi-Metal Defrost Thermostat

If ice is building up in your freezer or if your freezer is getting too warm on the defrost cycle you may need to replace the bi-metal thermostat.

$171.00

Emitter and Receiver Boards

These boards tells the icemaker when it's full and that it has to dump the ice, and it also tells the icemaker when to refill with water.

$83.88

Condenser Fan Motor Kit

This kit includes the motor, fan blade, wire harness and screws. NOTE: The manufacturer has changed the product to appear different than the original, but will still function the same as the original part. It is an OEM factory replacement.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No ice

  • Customer: Daniel from Suwanee GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 380 of 452 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

there were directions

  • Customer: Kate from Jacksonville FL
  • Difficulty: Very Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 567 of 1010 people found this instruction helpful
We didn't know where the product went and it was very difficult to install. read more

Ice maker stopped functioning

  • Customer: Phil from Auberry CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 311 of 326 people found this instruction helpful
Remove the icemaker service door... gently pry the door pins from the hinge sockets. Remove the 3 screws from the under side of the icemaker with a nut driver (1/4"). Gently remove the icemaker . It's a tight fit between the top of the compartment and the icemaker lower support tray. Next, disconnect the electrical connector at the right side. You're do... read more