Make sure you haven't got the discount earlier.
Igniter Switch Assembly with Leads WP74007806
Fits your MGC5536BDW!
Rated by 5 customers
Really Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
$
157.09
In Stock
Get FREE EconoShip on orders over $100! T&C apply
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Fits your MGC5536BDW!
PartSelect Number PS11744205
Manufacturer Part Number WP74007806
Manufactured by
Whirlpool
Troubleshooting
This part fixes the following symptoms:
Will Not Start
This part works with the following products:
Cooktop.
This part works with the following products:
Amana, Magic Chef, Maytag.
Part# WP74007806 replaces these:
74007806
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 5 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
ignightor switches needed replacement
replacement harness was an exact replacement except the connector for the supply side. the cook top had a female spade connector and the new harness had a female single pin connector. i had to replace the connector on the harness.
-
Ocie from Anchorage, AK
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
While cleaning dripped fluid into Igniter Assembly
I shorted out the igniter assembly snd called a recommended repairman. He came over and called the appliance warehouse he deals with and they quoted him $169.00 for the part with 15 to 20 working days for delivery. He told me it will be a total of $300.00 to repair. After he left I checked on your website and found the part and ordered it
... Read more
. It took 2 days for delivery and was less than $30.00. After reading your simple instructions it took less than 30 min to repair. I took the screws holding the burners off and raised the burner assembly. I removed the old ignitor assembly and installed the new. The lead attachments were different so I cut and spliced the old attachment onto the new. Easy.
Read less
-
William from Henderson, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
0 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electric sparker/ignitor quit working
Remove burner covers (2 screws each)
Unplug hot and neutral leads (spade terminals).
Pull spark units off individual controls.
Attach new spark units to individual controls.
Cut end off hot lead (modification required as new lead came with round terminal instead of spade terminal).
Attach and crimp new spade termi ... Read more nal to hot wire then plug together.
Replace burner covers.
Test for function.
Repair complete.
Unplug hot and neutral leads (spade terminals).
Pull spark units off individual controls.
Attach new spark units to individual controls.
Cut end off hot lead (modification required as new lead came with round terminal instead of spade terminal).
Attach and crimp new spade termi ... Read more nal to hot wire then plug together.
Replace burner covers.
Test for function.
Repair complete.
Read less
-
Robert from Point, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
11 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner wouldn't light
In cleaning range top with control knobs off, cleaner splashed onto the plastic sandwich containing wires, etc. "spark spark whoosh puff." Turned off electricity, removed sandwich which controled the burner which didn't light and discovered a cooked interior. Going to PartSelect, matched model number, drawing of part, click, order, wai
... Read more
t one day. Each burner had to be removed with the star-flower screwdriver, range lid removed. The assembly was a connected set of five. Unsnap old, Insnap new. Easy, peasy. The difficult part was elevating the range tray with one knee to a level where the burners could be screwed back in. It works! New widow, I didn't need directions or physical assistance. Just make certain you have that special little screw driver to remove the burner.
Read less
-
Nancy from Lancaster, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water has found its way into the range and shorted the ingnition switch/wire lead assembly and shorted.
I removed the unit from the countertop after turning off and disconnecting the gas. I removed the top panel of the range by removing the burner bases held in place with two torx screws each. Remove the knobs and the whole panel will lift off. After the panel is off the wire lead assembly will just pull off and unplug. The new one is a
... Read more
direct fit. Assemble with the reverse order of disassembly.
Read less
-
CHRISTOPHER from HOUSTON, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11744205
Manufacturer Part Number: WP74007806
Manufacturer Part Number: WP74007806
Brand
Model Number
Description
Back to Top
Igniter Switch Assembly with Leads
$
157.09
In Stock
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.