Quick Question!

Have you ever purchased from PartSelect.com before?

11742543-1-S-Whirlpool-WP4449259-Inner Door Glass
11742543-1-S-Whirlpool-WP4449259-Inner Door Glass 11742543-2-S-Whirlpool-WP4449259-Inner Door Glass http://www.partselect.com/Schematics/Whirlpool/YGOCPFFC.gif

Inner Door Glass

PartSelect Number PS11742543

Manufacturer Part Number WP4449259
Manufactured by Whirlpool

This inner door glass is a heat resistant part that fits into a stove, oven, wall oven, cooktop, or range as the inner glass panel of the appliance door. The glass panel allows you to see the items being cooked or heated in the appliance. Handle with caution and be sure to use gloves, as the door is heavy and the glass is breakable. Do not replace the glass until the appliance is cool to the touch. This genuine manufacturer part is approximately 20 inches by 10 inches. Inner glass door is sold individually, and contains the glass panel only.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

Compare At

$67.03

You Save

$11.17

Your Price

$55.86
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.0 / 5.0, 40 reviews What's this?
 

5 of 6 people found this instruction helpful

Parts Used:
  • Inner Door Glass
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Kel from Denver, CO

Replacing inner glass on oven door

The other comments from folks who had done this were very helpful!
I had to go look up the directions for removing the door. To do this flip the latches on the hinges and then close the door as far as you can and pull up, it will come out.
Now lay the door flat on the kitchen counter and take out the 6 screws you can see on the edges and inside of the door. They are all the same so you don't have to keep them organized. Now you can take off the outer door with the handle (lift the inner door out since you will have the door face down at this point) and get it out if the way. Remove the hinges and set them aside but don't get them mixed up.
Next, take out the screws on the inner glass rails, there are two rails. Keep those rails in order for replacement. Take out the middle glass and clean it (this took oven cleaner and a razor blade on the one I had).
Take the middle of the door apart and expose the soft gasket (don't move it!). Clean out any broken glass and Insert your new glass. Put the middle piece of the door back on and line up all the screw holes! Put the first of the glass rails back on and the cleaned middle glass back in place, then the second glass rail. Put in the two screws that hold the glass rails.
Now you are ready to put the door back together. USE THE BOX TO HOLD THE DOOR OFF THE COUNTER WHILE YOU PUT THE HINGES BACK IN AND PUT THE DOOR FRONT BACK ON! If the screw holes don't all line up start the screws and work your way around, you'll get them to go in.
Voila! Door fixed.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 8 people found this instruction helpful

Parts Used:
  • Inner Door Glass
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers
Customer: R G from Orlando, FL

Taking the door apart.

This was more difficult than anticipated - probably because I'd never done it before. Once I got the door off (I didn't have the proper pins and used nails but didn't realize they had to be headless) I found all the screws, which were relatively easy to take out. I was surprised that the thermal door glass was obscured by two other panes of glass. It took more disassembly than anticipated and a few false starts when reassembling, but all in all it got done. I was happy that a job that would have cost probably $300 or more ended up getting done for $40 plus my labor - which isn't worth much these days. I'd certaily do it again.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 5 people found this instruction helpful

Parts Used:
  • Inner Door Glass
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers
Customer: Diane from Citrus Heights, CA

Broken inner glass on oven door by a grandmother who should know better!

After reading all the other entries, I decided that I could do this! My first hurdle was getting the oven door off the hinges. Mine were not like any of the others described. My son-in-law looked at them and couldn't figure them out. So, I found the original installation instructions and, lo and behold, they said to flip the lever (one finger operation) in each of the rectangular holes holding the door onto the oven and then lift up until the door comes off. I did it, and it did! Boy, is it heavy! From there I just followed everyone else's instruction about undoing the screws, washing the glass panels, lining up the screw holes to get it back together, etc. One thing that took me longer was that the steel panel needs to go back the way it came out, not flipped! When I washed the glass panel it held, I put it down wrong and then "installed" it backwards. Luckily, I have a double oven and looked at the other one to see what was holding up the re-assembly! I'm glad that one of the others mentioned that the glass on the "bottom", the one that broke, isn't held in my screws or steel plates -- nothing, so I wasn't surprised when I got to it and it was "floating" on the insulation. My white insulation was like a fine fiberglass and was easy to stuff back in around the rim of the new glass. Took me a little over one hour. So, no more wet rags on hot glass (you'd think after living 72 years that I would remember this!) The glass fit perfectly and my husband would have been proud of me -- that I tackled a job that he usually handled, and that I saved over $200 for a couple of hours of labor and travel time.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Inner Door Glass
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Mark from Kingsport, TN

Replacement of inner glass

Opened overn door and inserted allen wrenchs through the holes in the door hinges. Close the door until it makes contact with the allen wrenchs, then grasp the oven door handle and the bottom of the oven door and lift up to remove the door. Place the door on a flat surface,(I used a bed) and remove the screws to gain access to the glass. Upon re-assesbly, leave door flat line up and re-install all screws before putting the front pannel back on. Insert door back into the oven and open, remove the allen wrenches and close the door. The process is easy and will take 30 minutes to an hour and save you a $100.00 service call!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Inner Door Glass
Level of Difficulty: Difficult
Time to do repair: More than 2 hours
Tools: Screw drivers
Customer: nancy from edison, NJ

Glass on oven door was broken

removed door from oven, took all screws off door to remove glass, put new glass in place, put oven door back together, put oven door back onto the oven

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: William from Dumfries, VA

Inside oven door glass was broken and door was not closing completely.

I removed the door from the oven by locking the hinges with the built-in locks leaving the door open about 20 degrees. the door can then be lifted slightly off the hinges and pulled out at the bottom while tilting the top inward to remove it from the oven. With the door laying on a suitable surface with the outside face down, I removed about 6 or 8 screws from the door inside panel freeing the springs and the inside panel from the middle and front panels. Care must be taken to note from which locations the pointed self-taping screws come as opposed to the narrower-thread machine screws that hold the springs. Note: The inside panel does not need to be removed! Once the inside panel is freed from the inner panels, using suction cups the glass can be lifted slightly and slid toward the bottom of the door, rotated slightly, and removed through the window hole in the back face of the door. The new glass is installed in a similar way using suction cups by maneuvering it at a angle through window hole and into its frame. The hinges were replaced by lifting the bottom of the inner door panel slightly to clear the hinge and swapping in the new ones. Be sure to observe the difference between the left and right hinges in the location of the screw hole at the bottom of each hinge The narrow-thread machine screws that hold the hinges to the inside panel should be installed first while you can get you hand inside the door to hold each hinge in alignment with the screw holes while you start each screw. Re-install the pointed self tapping screws by pressing down on the rear panel to collapse the spring-action glass frames within the door so that the short screws will reach their threaded hole. Be careful to back off the self tapping screws first until you feel a click into the original threads to avoid stripping the holes. Last re-install the door on the oven. The replacement hinges should have come with the springs already "cocked" with the built in locks in place. Install the door with it in tan almost-closed position by sliding the hinge extensions into the slots in the oven. Once the extensions are properly in the slots the door can be fully opened and the built-in hinge locks re-positioned to the unlocked position to allow the door to fully close. Should you accidentally release only one of the hinge locks in trying to insert the hinge extensions into the slots you will have to reset the hinge. If the door is free from the oven, this may require a pair of heavy pliers, like channel lock pliers, to re-tension the hinge spring and "cock" the hinge extension by re-positioning the built-in lock in the locked position. If the hinge lock on one side of the door releases, but the the opposite side hinge extension is not fully inserted into the oven slot I recommend carefully moving the door to the fully open position, being careful to avoid twisting the inserted spring's extension, so that the hinge lock can be re-positioned to the locked position, the door full removed, and start again to install it. It helps to have two persons to hold opposite sides of the door for this operation as the door is heavy, but not essential. When in the proper position the hinge extensions may not appear fully inserted, but this is normal to allow for closing of the built in locks. It helps to observe how much of the hinge extension is exposed either before removing the door initially, or, if you have a double oven, looking at the hinges on the door of the other oven. Good luck with your repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Inner Door Glass
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Janene from ORLANDO, FL

Inner glass was broken by previous tenants

Read all the way through this once before doing it. It really helps in keeping pieces and parts separated. First I had to take off the oven door. Please do this as it will make your life so much easier! The owners instructions does a lousy job explaining how to do this. You need to insert a small Allen wrench into the holes behind the door hinge pin. Just stick them in there and leave them. If you don't have Allen wrenches you can use small nails or the like, but you have to put something into the holes. Close the door slowly, yes it will feel like you are going to break the hinges or the wrenches. When you get the door almost completely closed you should wiggle the door a bit by the handle and pull up. The door will come off. Once you get the door off you can get to work. Leave these wrenches in the hinge holes. You will need a flat surface big enough to lay the door down to work on it. Lay it down with the handle towards the surface and the broken glass facing you. Remove the 4 screws on the broken glass side, the 2 screws holding the brackets on the bottom and the 2 screws on the top of the door. You will need to wiggle the inside cover off because there are 2 little clips at the top you need to get it off of the outer glass door. You should have 2 separate pieces, the outer glass of the door and the inner tempered glass and sheet metal portion of the door. Set the outer glass door aside, somewhere safe, as you really don't want to have to reorder that part too! From there you can lay the door down with the broken inner door glass towards the work surface. Remove the screws and good pieces of glass and lay them down in the order you take them out. This helps putting them back together later. Keep the pieces together in sets so you know which set goes to each section. There should be 3 pieces of glass total in the assembly. You remove the screws and the 2 good pieces of glass. The inside door glass is accessible under a large piece of sheet metal held in place by little flanges cut into it. You can remove this sheet metal panel piece by wiggling it out away from under the hinges and away from the hinge end. There is a piece of insulation under there as well. Make sure you reseat it correctly when you put it all back together. If you don't it will stick out, and make things hard to line up. Pull the broken glass out, Put the new glass in and replace the sheet metal panel. At this point I would suggest putting the four screws you took out at the very beginning from the inside of the door back in. They keep the 2 hinge assemblies in place and they will be harder to line up if you don't. You need to work from the bottom side up but it's pretty easy to get the 4 screws back in. Don't be afraid to wiggle the pieces around so you can line up the holes. They need to line up so that the hinges line up back to the oven. Reverse how you took the other glass pieces out and put the door back together. Put the front glass piece back on and secure it in place with the bottom door brackets and screws and the top 2 screws. Lift the door unit back up by the handle and place it in the slots for the hinges exactly the way you removed it. You will feel it sort of catch when you pull the door open slowly. Remove the Allen wrenches and you are done.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Inner Door Glass
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Michael from LAKE FOREST, CA

Inner glass door shattered

Unlocked the latches that hold door into oven. Removed door to work on it. Disassembled door by removing all the screws that hold it together. Removed two other glass sheets to access location. Cleaned out broken glass. Installed new glass sheet and reinstalled two other glass sheets. Reassembled door and reinstalled in oven. Not difficult, just a fair number of parts and pieces to take apart and put back together.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Inner Door Glass
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: alvin from st. louis park, MN

Broken inner door glass

Removed the door from the oven. Undid all the parts above the inner glass door. Installed the inner glass and reassembled the door. Reinstalled oven door.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
  • Inner Door Glass
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Alan from Prairieville, LA

Cracked in oven door glass

Read the instructions in installation manual to remove door. Kept removing screws. Was surprised to find two panes of glass between the inner glass and the outer glass. Cleaned all the glass (4) and the inside of the door. Looks brand new. Be careful with the insulation; be sure it is pushed back or it will show from the outside.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
  • Inner Door Glass
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: ariel from tarzana, CA

Inner glass dooe cracked due to thermal stress

I removed the Oven door, unscrew 10 screws, open up the dor case, clean all glass levels, replace inner glass, reassembled the door, reinstalled the door to the appliance.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
  • Inner Door Glass
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Bill from Sedalia, CO

Inner oven glass cracked

With just the removal of a few screws I was able to replace the glass with the side benefit of cleaning the outter glass that had gotten dirty over the years with use. This is a simple project that all can complete.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Inner Door Glass
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: J from Niceville, FL

Inner glass broken

fairly easy. took a while to reassemble. otherwise all was ok.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Inner Door Glass
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Kimberley from Gilberts, IL

Inside oven glassed cracked.

First I removed the door from the double oven as instructed in the owner's manual. Then I removed the screws holding the door together. I removed the layers necessary to get to the inner door glass. Then reassemled it in the order that I had taken it apart. A total of 15 screws. My tip would be pay close attention to how you disassemble.
Not only did we save the cost of a repairman but because of Part Select we got the glass for less than half the price quoted to us from Kitchen Aid for the part and delivery.
Very satisfied with our experience with Parts Select

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Inner Door Glass
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Dennis from Rowlett, TX

Wife broke inside glass, cooking no less...

removed door, took out 8-9 screws, slid door upward, and removed. took out broken glass, and replaced.

Help other customers find the most helpful instructions.

Were these instructions helpful?