This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Washer Dryer Combo.
This part works with the following products:
Maytag.
Part# WP22002437 replaces these:
AP6006293, 22002437
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Luisa P - June 12, 2018
Verified Purchase
Water Inlet Valve - 4 coil replacement for Maytag washer
This was *exactly* the part we needed to replace the old valve. The installation was easy, and I was back to doing laundry within a couple of hours.Thank you for having the right part for what is not a particularly new machine (only about 15 years old), but certainly a good one worth repairing.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 2.8 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Water would continue to flow into Washer even after washing machine was off
The best way to access the water value was through the rear of the stackable washer/dryer by removing the back access panel (3 screws with nut driver). It was also necessary to remove the large back panel where you access the drive belt to get you hands up to the valve. It was a little tight accessing the valve unit from the back but de
... Read morefinitely better then removing alot more to access through the front.
Once the back access panels are off you will see the blue water valve. it has (3) water hose connections and (5) electrical connections. Make sure to label each of the water hoses and electrical connections before removing them. The hoses simply are held on by hose clamps (use a screw driver) and the electrical connections just slide off the contact conductors. Real simple but again it is a bit tight working from the small access panel.
I marked all of the hose and electrical connections prior to removing anything. The removed all connections and slipped out the water valve. Simple reconnected water hoses and electrical connections replaced both access panels and all systems were a go.
Definitely a relatively easy fix for a do it yourself project. Part was only $70 (included shipping). Repair cost for the Maytag man was quoted at $450 for visit labor and parts.
Read less
Brian from Mount Airy, MD
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
31 of 34 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cold Water Valve bad
This is a stack unit. The service manual describes the repair by going in from the front of the washer. I found it much quicker by the back. Take the large panel off the rear of washer. Take 2 screws out of the H/C connection panel and work it to the inside of the washer. Next you will be able to turn it enough to get to a single screw on
... Read more the right side that holds the valve assembly to the support panel. Take it out and now you can slide the valve assembly to the right and release it from the support panel. Drop the panel down and out of the washer. Next mark electrical connections and unplug all. Start on the left and take off all 3 hoses careful not to mix them up and re-attach to new valve assembly. Hook up electrical plugs, re-attach to support panel and work the panel through the opening and re-attach to the outside of washer. It is a little tight working in close quarters, but will save lots of time. This was much less involved that trying to get to the valve assembly from the front!
Read less
David L from Cleveland,, OK
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
25 of 26 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Timothy
January 27, 2022
This is a Maytag stacked washer/dryer unit.
The Water Inlet Valve assemble has 4 solenoids. All other washers I've worked on only had 2. The first 2 inlet solenoids look like they control the hot and cold inlet. What is the purpose of the other 2 solenoids?
I also would like to replace the 2 caps that are across the inlet solenoids, which shown in the wire diagram, but no where else that I can find. What is the part number for those caps?
For model number MLE2000AYW
Hi Timothy,
Thank you for your question. One line should go to the dispenser and the other to the ice maker. There are some instructions listed for the part on our website that you may reference on how to install it and we have included a link to one of our YouTube videos that you may reference on how to install the water inlet valve. The refrigerator and the water inlet valve in the video may appear different from yours, but it will give you a general idea on how to install the part. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
