Quick Question!

Have you ever purchased from PartSelect.com before?

11738882-1-S-Whirlpool-WP21352320-Drive Belt - 51 inches long
11738882-1-S-Whirlpool-WP21352320-Drive Belt - 51 inches long 11738882-2-S-Whirlpool-WP21352320-Drive Belt - 51 inches long 11738882-3-S-Whirlpool-WP21352320-Drive Belt - 51 inches long http://www.partselect.com/Schematics/Maytag/48377.gif

Drive Belt - 51 inches long

PartSelect Number PS11738882

This V-style drive belt is about 51" long and 3/8" wide. This part is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Burning smell.
  • Noisy.
  • Pumps but will not spin.
  • Spins slowly.
  • Will not drain.
  • Shakes and moves.
  • Will not agitate.
  • Will Not Start.
  • Leaking.

Compare At

$12.91

You Save

$2.15

Your Price

$10.76
Order within the next 4 hrs and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 67 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used:
  • Drive Belt - 51 inches long
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: william from cypress, TX

Squeel

Tilted machine back, put a paint can under it and did R & R with belts.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: mark from 29 Palms, CA

Belt and motor pulley burnt up. Did not know the cause

Just tipped it back pulled the pulley off (the little plastic tits on the shaft just break off) the belt comes off easy. Carefully tap the new pulley on using a little grease or petroleum jelly on the splines before hand. The belt goes on easily when you slide the motor over. Just force the belt onto the big pulley just as you would on your car.
Problem was... the new belt and pulley burnt right up again when it tried to agitate after filling. So the motor was turning fine, and the pump shaft was turning fine, but the agitator (tranny) must have been locked up. Its pulley (the big one) would spin in one direction but was locked in the other when I checked it. Not knowing any better, I assumed that was normal. I still don't know if it is or not. That's the problem with these chat sessions...One guy says it should spin freely both ways another says it should be somewhat difficult to spin, you don't know if the control has to be set in a certain spot before checking. I gave up just going to buy another. This time a direct drive, although it doesn't make any difference there all junk.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Drive Belt - 51 inches long
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Socket set, Wrench (Adjustable)
Customer: Niels from Hopewell Junction, NY

Broken belt needed to be replaced.

Replacing a belt on a washing machine is a pretty easy process, depending slightly on how easy it is to access the belt. On our Maytag, the belt can be accessed directly underneith the washing machine. So, I lifted the front of the machine and put a few blocks of scrap wood under the legs to hold up the front of the machine. Once that was done, there was nothing else that needed to be removed to access the pullies that the belt had to go around. The motor itself is generally adjustable to allow the belt to be changed. So, I first wrapped the belt around the largest one that spins the washin machine tub, and then wrapped it around the one that spins the water pump. Finally, I loosened the bolt on the motor to allow it to move, wrapped the belt around the motor, pulled the motor back to tighten up the belt, and tightened the bolt that holds the motor in place. It's a pretty straight forward repair that narly anyone could do thmselves.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Drive Belt - 51 inches long
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Michael from Mokena, IL

Had a squeaky belt

Piece of cake. Raise up the front of the machine. the belt slips of easy by turning the main drive wheel. put the belt on the two small one and then rotate the big wheel as you slip the belt into the grove. good idea to first clean the wheels of any old belt material that may be worn off. Piece of cake!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Drive Belt - 51 inches long
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: john from mashpee, MA

Would not engage spin cycle, belt was shredding.

pulled the machine out, tilted it backward to expose the bottom. pulled off the old belt. got the new belt started on the three pulleys. pulled the belt to spin it , and...............done !!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Drive Belt - 51 inches long
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Mark from Isom, KY

Water leaking from under front of washer

after doing some research I found out that a loose or slipping water pump belt could cause the water pump to not pump out the water correctly. Under the washer is the belt. All you do is have someone lift the front of the washer up enough that you can reach under and remove the belt. Then replace the belt back like you took it off.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Drive Belt - 51 inches long
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Jeff from Sugar Land, TX

Machine was wailing like a stuck pig!

Pulled that sucker out from the wall and leaned him back just enough to prop a case a beer under it. Slid up under there with the biggest dust bunny I ever seen. Yanked that old belt off and threw it away. Tried to uncoil the new one and it slapped me in the nose! Got it uncoiled and around the two smaller pulleys pulling the adjustable one in to it's limit and walked the belt around the big drum pulley. By the time my wife put down her coffee and came to see if she can lend me a hand I was done!.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: Craig from Mount Shasta, CA

Washer tub stopped turnig and motor made a humming sound

Removed top cover, then removed front cover. Put washer on its side and removed belt. Located motor, noted orientation of retainer wire(v shaped wire that clips motor to frame), removed motor, noted wiring diagram on paper before removing wires from termination points, removed wires. installed new motor, installed wiring, installed wire clip. Turned washer on side and installed new belt. Turned machine on and it worked great.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 7 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: More than 2 hours
Tools: Screw drivers, Socket set
Customer: Mark from Alamogordo, NM

13 years of daily use and parts needed replaced

The repair of the four parts, motor, timer, pump and belt only took about 3.5 hours. Simply find the screws or bolts holding the part in place and undo... The place the new part back to match the holes and bolt back down... Match the wiring of the motor by moving one wire at a time. (don't pull the all off at the same time) ... And the price is wonderful... I now have a washer that will last another 10 years or more... Very easy very satisfied.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Drive Belt - 51 inches long
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Virginia from Rockford, IL

Machine was starting to make noises when spinning

My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Drive Belt - 51 inches long
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: FRANK from CHULA VISTA, CA

Water not draining

changed drive belt and saved me from buying new washer,,working like bland new again ...many thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: ALISON from MARTINEZ, GA

Water leaking on floor

Removed back access cover and lift top cover looking for leak. Initially thought it may have been the pump housing. I filled some water into the tub and I flexed the hose between the tub and the pump and water sprayed out. It had cracked in about 3 small places (water is present in the hose anytime water is in the tub) Ordered and replaced hose. Also order drive belt and replaced as a preventive maintenance item.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Jose from Elizabeth, NJ

Made noise during washing and rinse cycle

It was easy to replace the water pump

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Jeffrey from Flat Rock, MI

Broken belt and motor pulley

Repair was very easy. I removed the old pulley from the motor shaft by breaking it. And then tapped the new one into place. It works great. DON'T buy a new motor for $120, just replace the pulley $6. This whirlpool pulley fits the Admiral motor perfectly!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Drive Belt - 51 inches long
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Richard from Ponte Vedra Bch, FL

Machine woulden't spin properly

diagnosed a loose belt-- ordered and received same -- installed and set to proper tension that was simple.

Help other customers find the most helpful instructions.

Were these instructions helpful?