ZSGW420DMD General Electric Refrigerator - Instructions

1. Removed and tested defrost heater, tests good. 2. Reinstalled defrost heater. 3. Removed and tested defrost over-temperature sensor, tests good. 4. Reinstalled over-temperature sensor using soldering iron, dielectric silicone grease, and heat-shrink tubing. 5. Removed the control printed circuit board and checked for blown fuse's, fuse's are all good. 6. Removed the defrost relay from the printed circuit board using soldering iron, bench tested the relay, it is good. 7. Soldered defrost relay back onto the circuit board, and reinstalled control board. 8. Removed and bench tested evaporator thermistor, the resistance is out of specification, ordered new thermister. 9. Installed new thermistor using soldering iron, dielectric silicone grease, and heat-shrink tubing. 10. Re-assembled refrigerator. 11. Installed temperature monitoring and recording instrumentation for 72 hour test. The defrost cycle is running correctly with a defrost termination temperature of around 90 deg-f. The defrost cycle ran twice while running the 72 hour test. 11. Removed test instrumentation and Put the unit back into service, The thermistor was the culprit. I bought the right part on the first shot, nice.

Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.

Ironically I did this today, as this email request came up asking how it went. I'm not a repairman, I'm a software engineer, and I can't thank this site enough for the step by step videos. With the video to help, this was a breeze, I was nervous as I had to empty all my freezer out onto the living room floor. Once that was done the repair took about 30 minutes. Thank you partselect!!!!! My second time doing business here, and I'll be coming back (well, if something breaks, so let's hope I don't have to).

I watched the Video on partselect website for replacing the Solenoid. The repair went smooth. No problem.

watched a 2 minute video on installing the connector. Then using the utlity blade cut out a 1/3" section of the tubing and installed the connector. DONE! Leak fixed

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

I followed the video instructions. They were clear and consise. I removed the trim ring and controls. Them removed the housing and flapper. I did notice a small burr in the plastic chute and foam insulation. I trimmed this off with a utility in hopes this burr caused the flapper to warp. This is the 2nd time the flapper has been replaced in 1.5 yrs. The repair was really easy thanks to the video.

Very easy to replace these parts. Thankas to part select for telling me how to do it. You are very helpful.

remove 3 bucket screws. 1 bracket screw slide bucket back insert drive reverseb steps

SO easy, just took the old one off and popped the new one in. Why I am bothering to write this is that the first time I ordered the wrong part. I got it so quickly and the refund was made as quickly. Then I tried again and I got it right thet second time. Thanks, Mary

unscrew filter and replace the new one

I removed the front of the unit assembly and removed the entire auger unit and drive assembly. I married the old drive cup and new drive cup back to back using vise grip pliers, drilled 4 3mm holes, installed 4 phillips head stainless steel screws and, using an emory wheel, ground off the exposed screw ends. I then re-installed the drive assembly and auger unit. This increased the length of the drive cup allowing the drive to fit without any slippage. The entire cost was less than $18.00 including shipping and screws and took about 1 hour. It works great.

My husband made the replaced the flapper while watching the video provided in your email, it was easy. Thank you.

Followed the video directions. Spent about 5 minutes and I was done. Very easy to do. Problem with frost is gone. The video makes it easy to remove the plastic parts without any damage.

exactly as described in your video.