All Installation Instructions for General Electric Microwave ZSA2201RSS02

Could not find the part at the big box stores - HD or Loew's

Removed the glass shield and inserted the 2 bulbs. Then replaced the glass shield.

The staff were terrific. Thanks so much as it had a happy ending.

Anita

Parts Used:

Halogen Light Bulb - 120V 20W

Anita M from Rochester, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

bulbs for sueface light burned out

Removed screw holding faceplate that covered bulbs. Next inserted new bulbs into sockets.
Turned on surface light to insure they worked - they did. Re-attached faceplate.

Parts Used:

Halogen Light Bulb - 120V 20W

Raymond from Ashland, VT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bulbs Burnt Out

Removed old bulbs replaced with new. Bulb fit perfect thank you

Parts Used:

Halogen Light Bulb - 120V 20W

DOMINICK from VENICE, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

microwave lamp was burned out

took glass cover off being an electrician and saw lamp or bulb was burned out. googled your site and with model number.went on partselect found lamp,orderd it.2 days later lamp arived installed lamp. So easy no running around or making several calls

Parts Used:

Halogen Light Bulb - 120V 20W

Timothy from Swampscott, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Light Bulbs Failed

Used a phillips screwdriver to remove the screw holding the light cover in place. Removed the two bulbs and replaced them. Closed the cover and tightened the screw

Parts Used:

Halogen Light Bulb - 120V 20W

Wilbert from Stephens City, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The halogen bulb had blown

It was just a matter of removing the old bulb and easily putting the new one in place. Very simple repair and the bulb was received amazingly fast. Was no doubt the best service I have received and I appreciate the quick response.

Parts Used:

Halogen Light Bulb - 120V 20W

Norma from De Moines, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Micro was not producing heat.

Removed unit from above range. (A two person task.) Removed display panel, disconnecting wires from plugins. Removed outer cover to access magnetron. Used camera to take photos before disconnecting other wires. Replaced magnetron and reconnected wires, double checking with photo. Tested prior to reinstalling. It works fine.

Parts Used:

MAGNETRON

Sal from Center Moriches, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

interior/exterior bulb replacement

Inside "cavity" bulb was a PITA. Need to remove top decorative trim (2 screws and tabs) to access bulb housing. Broke 1 screw tab so be careful (Wiggle it more). Acccess to bulb housing was made for younger smaller hands, attached by 1 screw. Remove screw, rotate housing, replace bulb. Reverse proceedure. Outside bulb, cake...1 screw, drop lens replace bulb, your done.

Parts Used:

Halogen Light Bulb - 120V 20W

Gerry from New Milford, CT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No heat.

Replaced the fuse. Result; did not fix the problem.

Parts Used:

FUSE

Mack from Jacksonville, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

failed bulb

unscrew one screw and remove bulb and insert new bulb and replace lense with one screw-

as easy as it gets-

Parts Used:

Halogen Light Bulb - 120V 20W

Billy from Palm Desert, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Surface light bulbs burned out under microwave

Unscrew (one screw) and take off the cover of the surface light under the microwave (the light over the stove). Firmly pull out the old light bulbs. Align the two prongs of the new bulbs into the socket and firmly push into the recepticle. Replace the cover and screw.

Parts Used:

Halogen Light Bulb - 120V 20W

Thomas from Laguna Niguel, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Had to replace to halogen lamps

Repair was simple; only a phillips head screw driver was required to remove the access plate.

Part Select delivered the replacement lamps within 3 days from the date I placed the order - great service.

Parts Used:

Halogen Light Bulb - 120V 20W