YWED9600TU0 Whirlpool Dryer - Instructions

replsce

First removed and checked the ignighter. It was fine. Next I located the schematic drawing and discovered that the burner, ignighter, and flame detector were all operated by one simple 110 volt circuit. This circuit did not power up when the dryer was cycled on. I pulled the dryer from the wall, removed the back panel, the vent etc. I then located the operating thermostat and the thermal fuze. The thermal fuze was open. (GOOD NEWS AN EASY FIX!!!) Thanks Guys

Well the video showed us taking off the back. Which wouldn't come off. Welded. Then we could not find the fuse in back of the unit or bottom. The second time we tried we found it in the front. We had to take off the front, bottom cover then we found the fuse. But, it didn't fix the problem. The unit is still on Casual load only. When we push the buttons the other lights light up but goes back to Casual. The unit is clear of lint and still drys but only at the Casual setting.

Pushed the new catch in by hand. Working great.

Went to your web site and found 40% of the time the thermal fuse is the problem. By using your site found how to locate fuse & test it. It took me 10 min to take out the old part & tested it to find it bad. I ordered the part which cost $10 & got it in 3 days. It took me 10 min to install it and the dryer is fine. This save me a big repair bill.

4 screws very easy and you gave excellant directions on how to replace

just removed old fuse and installed new one ..... cleaned all the vents out to

Diagnosed the problem on parts select, ordered the part and watched the youtube video on how to install and done! Super easy - thanks for boosting my "chicks can fix anything" mojo and saving me a bunch of $$.

Saw no heat, web said probably the fuse. Replaced the fuse. Nope. Second guess was the thermostat at the exhaust. Replaced that. Nope. Finally got to actively troubleshooting and isolated one of the thermostats near the heating element. Replaced that and everything is fine. So now I have a good spare fuse and thermostat for the next repair. There was one tool I wished I had, a socket small enough to open the back. I had to use pliers and that was a pain. Other than that the repair was almost trivial, just unplug the bad one and plug in the good one.

Removed back panel of the dryer and located the thermal fuse. Disconnected two wires, and removed one screw holding the fuse in place. Installed new fuse and reassembled. Dryer works like a champ again.

I ordered the part with the manf. # BUT upon installation I found that the new part was slightly different than the old part therefore not allowing me to screw the new part to the inside of the dryer - I was able to find longer screws that would work but took me an hour to figure out what the issue was and then resolve the matter

Disconnect the power cord. Unhook the dryer vent hose. Remove the back. Find the Thermal Fuse. Use a ratchet and socket to remove socket head screw that holds the Thermal Fuse in place. Disconnect one of the two wires from the old Thermal Fuse and attach the wire to the new Thermal Fuse ensuring the wire is placed on the same end of the new Thermal Fuse as the old Thermal Fuse. Repeat procedure for the remaining wire and screw Thermal Fuse back in place. Replace the back, reattach the dryer vent hose and connect the power cord.

Repair was extremely easy. I looked on your parts web site and found my model number, read what the common causes of dryer not heating. I purchased both the Thermistor which I knew was bad after using my Omh meter and found a open circuit, and bought the High limit thermostat as maintenance. In addition to these parts I also purchased the heat element assembly which I could see was broke. In stalling all three parts was less than 15 minutes, less than $100 and WOW less than two days delivery !!! Great job I will re-order from you again! KIm Faught, League City, Texas

I watched the video provided first to get an idea of how it should go. The dryer I have had a different kind of door, so those instructions didn't apply. You probably don't want to publish the way I ended up fixing it, but it did work eventually. Saved me over $500!! Thank you!

I opened up the instrument panel box using philips screw driver and found the repair instructions. Followed the symtom diagnostic page and found that if the machine can be turned on but motor not working then check thermal fuse or motor. Next, I unplugged the appliance and remove the back panel to locate where the thermal fuse and other parts per the diagram in the repair instructions. Using a volt meter, I removed the electrical plugs to the thermal fuse and check resistance (a 1 on the volt meter indicated that the fuse is open (or burned)). Removed the thermal and checked for part number and looked up the model and parts number on the internet. Took a chance and ordered the part. When the order arrived 3 days later, I just simply replaced it and put everything back to where they were. Hooked up the power supply and turned on the dryer. It works again!! One thing I found was that I needed to clean the air pipe since it was totally clogged and probably caused the machine to overheat and burn out the fuse.