YWED94HEXL0 Whirlpool Dryer - Instructions

Disconnect the power cord. Unhook the dryer vent hose. Remove the back. Find the Thermal Fuse. Use a ratchet and socket to remove socket head screw that holds the Thermal Fuse in place. Disconnect one of the two wires from the old Thermal Fuse and attach the wire to the new Thermal Fuse ensuring the wire is placed on the same end of the new Thermal Fuse as the old Thermal Fuse. Repeat procedure for the remaining wire and screw Thermal Fuse back in place. Replace the back, reattach the dryer vent hose and connect the power cord.

took the back panel off by unscrewing all the little nuts..replaced thermal fuse and put back panel and screws back on...

Determined via multimeter that either the thermostat or thermal fuse were not working, so ordered the kit (best value, contains both parts).Easiest access is from the rear, so removed rear panel and top of dryer (required) and also the vent tube since it was in the way. Unhooked wires from both parts, used socket to remove nuts holding each one on, put new ones in place, re-attached wires. Replaced vent tube, vacuumed entire inside of dryer (good idea). Put back/top back on and the dryer worked/heated perfectly immediately.

Used wire schematic and locate thermal fuse. Disconnect power and remove rear panel. About 8 screws. Remove the two wires from fuse and check fuse continunity. Fuse was open and prevented power from going to gas solenoids. Replace fuse and clean exhaust ducts. Dirty ducts might have caused fused to over heat.

I went on the PartSelect site and watched some videos to determine what could be wrong. I almost guessed and bought the wrong part as there were a few. I ended up spending $17 for a multi tester. Once I determined that the thermal fuse was bad. I just followed the instructions from the video and replaced it. Took me more time figuring out what part was bad and buying the tester than actually replacing the part. Very glad I bought the multi tester watched the videos. After that it was easy.

Followed video found part son replaced it worked!

From the list of parts that most commonly fail causing the no heat condition I selected the most common part, the heating element. I replaced it according to the instructions on the associated video. It was very simple. Reinstalling a good vent for the dryer took longer. But the new heating element didnt fix the problem. So I replaced the termal fuse which was also very easy but also didn't fix the problem. At that point I decided to replace the dryer. In the process of recovering parts from the old dryer I noted a thin film of lint stuck to the smaller of the two thermostats. So I'd recommend first inspecting and cleaning all of the parts in the parts list before ordering new parts. But then begin with the most common failing part and working down the list. If you have some test equipment like a voltmeter, ohmmeter, or multimeter that would be a plus in isolating faults. Still, I'm a fan of PartSelect and would come here for other parts.

Put new heater in also new thermal fuse. Watched the vidio about install, video longer than repair bryon

Using some advice here on this website, and a youtube video found by searching for 'idler pulley replacement' I was able to fix my dryer! Taking off the screws was simple, I used a cordless drill. I have some trouble removing the kick panel, and bent the latches, so there is a small gap between the dryer door panel and the kick panel, but it still works fine. Of note, you DO NOT need to remove the back panel, something I did and cost me some time. I am a bigger guy, so maneuvering on the floor to rig the dryer belt around the new idler pulley "in the dark" was cumbersome, but doable. All in all, an easy enough project for under $30 and less than an hour of my time. Kudos to this website, first, for the super fast shipping, and secondly, the reviewers who posted some instruction. Great job!

Disconnect the dryer from the power source and vent hose. Using the nut driver, remove all hex screws and the electric access panel from back of dryer. Loosen the electrical service cable clamp screws with philips screw driver and disconnect the ground wire. Remove the top panel from the dryer cabinet and the screws that hold the electrical bus in place, then remove the back panel from the dryer. Feed the electrical cable through the cable clamp and rest the back of the dryer against the side. Remove the tri-ring and old idler pulley, then clean and lubricate (WD40) the axel, and install the new pulley and tri-ring. Replace the back panel and all screws.

This was so easy.On Parts Select I looked through the options of what might be wrong when my dryer stopped working. After ruling out any power problems and checking the door switch I moved onto the next possibility which was the thermal fuse. Although I did not have the equipment to check the old fuse to see if it was still functional, I took a chance and ordered the new thermal fuse for my model # dryer. At a total of around $20 (about 2/3 of that was expedited shipping at my choice) it was worth it to me to give this a try before calling a repairman for what might be a bigger and more expensive problem. The fuse came within 48 hours and I logged back onto Part Select to watch the very simple video of how to install. I removed the six screws from the back panel of my drier,located the old theremal fuse, removed the one screw securing it, disconnected the 2 wires from the old thermal fuse (which looked a little browned around the edges)and reattached the 2 wires to the new thermal fuse in the same manner. I then reattached the new fuse with the one screw and put the back panel back on my dryer. Set the time, and pressed the start button and it fired right up. So happy I didn't have to pay $200 plus for this simple repair. Trust me when I say you can do this yourself. Very straight forward and simple installation. Good Luck!

We had initially ordered the wrong parts, but I called them to send one of the parts back. While I was on the phone with the rep, we ordered what I thought would be the right part. By this time I had been without a dryer for 5 days. It was about 4 in the afternoon. I asked the rep if we could possibly get the part the next day, and she politely stated that she didn't think so. But, the very next afternoon, the part was sitting at my door! I replaced the part easily while watching the you-tube on their website, and had the dryer running like new again in about 10 minutes! And I am a woman! I saved $300 instead of buying a new dryer. We have ordered from Partsselect before, and will continue in the future. I would recommend them to anyone who has any kind of appliance repair issue.

Replace thermal fuse. Pulled off back panel. Removed old fuse. 2 screws w 1/8 nut driver make sure you mark the to power lines. Replaced and tested before putting back panel on. Very easy anyone could do it

C/0 both thermostat sensors and fixed dryer Had no heat out ohmed out the coil and it was ok So I ordered both sensors and replaced them and dryer worked great

Ordered a thermal fuse . Very fast service (24 hrs)put the fuse in and is now working again