Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Motor out
I found that the dryer would not start turning by itself. Could manually help it start and it would run fine. Anyway, after a new set of rollers, belt, etc. found that the motor still would not start by itself. Ordered new motor and it was taken care of. You have to take the back off, remove the belt and remove the tumbler. After that, it is fairly easy. Two screws hold the motor down and then you can take the whole motor assembly out. Be careful removing the fan as it takes a 3/8 socket drive and it is plastic. Two clips hold the motor to the assembly. Needle nose pliers takes care of it. Replace and all should be good.
actually i found your site before i even looked at the dryer,thats how i knew to check for the thermal fuse. I ordered the part and it was on my door in 36 hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)
After looking at the schematic to see what was in line with the motor, I found the fuse as the first item. I pulled the fuse out and used a multimeter to ohm out the fuse. Upon using the meter I found that the fuse was bad. I typed into Google my part number that was on the fuse and the PartSelect Website came up as one of the choices to pick from. When the part arrived approx. two days later I installed the fuse by first unplugging the dryer and then removing the bottom panel and removing the fuse from the exhaust by using a small 1/4 inch wrench and pulling out the old fuse. I installed the wires on the new fuse and re-installed and put the 1/4 inch screw back in. I started the dryer after plugging it back in and it worked like it should have. Thank you for the part and I have recommended your website to other people already.
My 14 year old son did it as I supervised! Pulled the dryer out on a dolly, unpluged the dyer, removed 9 hex head screws to remove the back cover, removed and replaced the thermal fuse, located next to the exhust outlet, set the cover back on, moved the dryer back in with the dolly. I had the thermal fuse over nighted to me for a total price of $35, figured I saved at least $150 on a service call by Whirpool.
high pitched squeaking noise when dryer is first started.
1. Disconnect dryer from electrical outlet. 2. Pull dryer out and disconnect the exhaust tube from the back. 3. Remove the screws at the top of the dryer back ( 3 ) and remove the top of the dryer. 4. The service instructions will be in a bracket on the top right. I didn't use them because I have done this job before. 5. Continue to remove the screws holding the back to the sides. There will be a lint collector attached to the back panel by three screws. This must be removed first, then the screws along the edge of the back panel. 6. Pull the back panel up and away from the sides and set aside. You will see two lower rollers attached to this panel. 7. Look under the drum and you will see a idler arm and roller in front of the electric motor and a little to the left. Notice that the drive belt is looped around the roller. Unloop the drive belt from idler and roller. 8. Lift the drum of the dryer up and out of the dryer. 9. Replace all the rollers (4) by removing the plastic "star" on the roller shaft. This can be done using a small screw driver. 10. Once the rollers are replaced, place the new drive belt, ribbed side facing the drum around the drum. Lift the drum up and into the dryer enclosure, making sure the rollers in the front of the drum are in the ridge groove. 11. Lift the back of the dryer in to the dryer enclosure, again making sure the rollers are in the rear groove. Turn the drum by hand to make sure the front seal is flush to the front of the dryer and that the front rollers are in the front groove. I2. Install drive belt around electric motor shaft ( ribbed side facing the shaft), lift idler arm up while running the non-ribbed side of the belt around the roller on the idler arm. 13. Install the back panel using the remaining screws. 14. Install the top of dryer by sliding it into the front panel and securing with the last three remaining screws, these 3 screws go on the top of the back panel. 15. Replace exhaust hose and replace dryer into space it formally occupied.
Found a service manual on-line for the Whirlpool Duet Dryer. Did the troubleshooting for the problem stated. Found the heater element to be bad (open circuit across heater block). Ordered new element from PartSelect.com and installed. Dryer now works like a charm and I didn't have to call a repairman.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.
I first went to your site and studied the parts diagram to see where the element was located. I then unplugged the dryer and pulled from the wall. After that I popped open the front cover and accessed the bottom of the dryer where the element was located. I then removed two screws that held the element in place and removed the wires to the element. After a little tug the old element came out. I slid the new one in place and connected the wiring and screws and replaced the cover and pluged it in. Works good as new...
I took off the front panel via 2 screws on the inside of the dryer with the top panel in the maintenance position. Pulled out the tub(cut my hand pretty bad in the process but continued). Did some cleaning and I had to google how the belt tensioner goes into place. Rather difficult on your own i held the belt and placed the tub back into place while placing the belt around the tub putting it in the correct area. thats pretty much it and began reinstalling the parts i had removed.. easy fix now that i have done it once. This is all after my landlords said they werent replacing it and just to have this one hauled off, so all in all i have a 26 dollar dryer now:)
Following the very helpful instructions that I found at PartSelect.com I was able to open the dryer and access the heating element which I suspected was bad. I realized later that I didn't need to open up as much as I did but the job was easy. In the future I would only open the panel below the door to access the element.
Just to make sure that it wasn't a problem with a thermostat or thermal fuse I also checked continuity from the temperature selector knob on the control panel to the heating element. When I verified continuity (zero resistance) I knew that the element was bad. Once I removed it I could see that one of the coils was broken and I should have just checked that first and not bothered opening up the control panel at the top.
Still it was less than an hour of work total. I have some experience with DIY projects but have not worked on appliances before. Thanks for the great site with good instructions and lower costs than the local parts counter.
It was easier to remove the blower manifold cover, (3 screws) to get at the heater element. Remove the heat shield, disconnect the two wires from the element. There is another screw on the side holding the element in the housing. Remove it and slide the element torward you. I used pliers as it was a snug fit. Replace. Good time to vacuum the whole area.
1st. i removed the two screws that holds the cover. 2nd. -vacumn (most time used)around to find the screws that hold the metal heat tube and shield. 3 rd. removing the screws tip the front of the tube up and pull out from the back.my element was clipped in place. I then pulled the element out and replaced the thermostat (tip: replace all t'stats around the heat element). it is as simple as reading the repair stories