Models > YMMV4203DW00 > Instructions

YMMV4203DW00 Whirlpool - Instructions

All Instructions for the YMMV4203DW00
16 - 25 of 25
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Turntable motor would not turn food tray
Replaced with new motor from Parts Select. Part was a correct replacement for the old one. perfect fit. Works like it did when it was new. I will recommend Parts Select to anyone. Thank you very much. I would definitely use your company again in the future. I saved $30 by not using parts from GE.
Parts Used:
Turntable Drive Motor
  • Richard from Magnolia, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
motor was slipping
replaced the drive motor and coupler coupler from samsung parts
Parts Used:
Turntable Drive Motor
  • John from Tipton, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
microwave acts like its working but won't heat.
Replaced the magnetron and diode. Microwave works prefect now.
Parts Used:
Microwave Magnetron
  • Mike from Paso Robles, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Rotating Tray fails to turn
Very easy. Opened the Microwave door, removed the dish and replaced the coupler.
Parts Used:
Coupler
  • JIM ODANIELL from WILMINGTON, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
tray would not rotate
Snapped the coupler in place. Took one minute.
Parts Used:
Coupler
  • Denise from Clovis, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The turntable on the Microwave stopped turning
Asked at Best Buy what our options were after I described the problem. They said to buy a new Microwave. I thought No way it is only a few years old. Whent home did som research and found your site and for under $5.00 My microwave turn table turns again!
Parts Used:
Coupler
  • Julie from Seattle, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Tray inside would not rotate
Removed old coupler with my fingers and installed new one on shaft. Works fine.
Parts Used:
Coupler
  • al from lexington, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Table Will Not Spin
Try to turn Coupler. If it is loose it is broken 1. pull old one out 2. line up keyway on new one and press it in. (If mild resistance was felt while turning coupler it is not coupler most likely drive motor)
Parts Used:
Coupler
  • scott from milwaukee, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
change old filter
replace filter according instruction
Parts Used:
Charcoal Filter
  • David from Simsbury, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Microwave Vent Hood Filters
Not so sure this would qualify as "instructions", but I only needed a screwdriver because the "D" rings of the old vent filters broke off and I had to pry to old ones out. Keep in mind, I am mechanically disadvantaged and can barely change an A/C filter ... that being said, all I did for this order was input my Model number and PartSelect found the correct replacement part. I receive the parts super quick (faster than the other 2 purchases I did that day). The only bummer was the packaging ... super huge box for small tiny parts. Otherwise, I now know where to go for replacement parts. This project should be a "no-brainer" for most DYI's, so getting the right parts with just a model number was lifesaving for me :0)
Parts Used:
Grease Filter
  • Vicki from Phoenix, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the YMMV4203DW00
16 - 25 of 25
Back to Top