Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The dryer wouldn't turn on after pushing the start button
I watched the video several times before beginning, which was very helpful. As I didn't have the tool that was recommended in the video, I used pliers, which although took longer, worked out fine. I also used pliers to pull the wires off of the old thermal fuse. My dryer had been not working for 2 months, so I was very pleased that I was able to watch a very detailed video, order the parts on the same website, and receive them very quickly (within couple of days.) My daughter who lives in another state googled my dryer model number with a description of the problem and found your website. She sent me the link of the video to watch as it appeared very easy to understand. She and I both were very impressed by the step-by-step instructions on the video, including a list of all the tools required. I am an 81 year old woman and had no problems fixing this by myself with the assistance of your website. I have recommended this site to several of many friends and family members. Thank you!
I use the manentance kit that was not the problem. I end buying the drive motor and that was it. I was happy with the service I got from part select, overnight mail what more could I ask for? I am also glad I replace everthing with mainentance kit. Thank you for your help john degnan
Followed the included instructions in the Maintenance kit. Very easy to understand & follow. Only advice is to have an extra set of hands to assist in re-installing drum w/ the new belt. Entire disassembly & reassembly could be done w/ basic hand tools but went alot quicker using a cordless drill w/ a set of nut/screw driver bits.
The problem was the dryer wouldn't heat up (gas). Would run but just not heat up.
So I opened the back up, and looked down the flame shoot and I could see that the igniter was never glowing red. (You can actually see the red glow of the igniter when its working right, then you here the solonoid click and flame. But again all this when its working correctly.) So anyway, no heat no glowing red.
I took the voltmeter out, grounded 1 lead and just followed the voltage (using the schematic provided), through the switches, yada yada trying to trace how far it got.
Voltage got to 1 side of thermal fuse, but not to other side. Bingo. Disconnected fuse and did continuity check - open. All of this took diagnosing took 1/2 hour to hour. Not really counting toward fix. Ordered the part at parts select. Put a jumper over the fuse so that clothes could still be dried (probably not recommended but it works). Part arrived in 2 days. Didn't even put the back panel on.
The part is right on the back. 1 screw, 2 space terminals. Takes all of 3 minutes to replace. Then another 5 minutes to put the back panel on and vent hose back on. Most of that is because you are working in a cramped space. (I don't have the biggest laundry room.)
Can't beat parts select!
Parts select + a little know how, saved me about $400.
removed cover then pulled wires with a plier, unscrewed the fuse and installed new fuse then put back cover plugged in power cord, fired dyer and run dryer for 2 minutes and felt warm air coming out of the exhaust.
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
dryer would not come on, light still worked, timer still ran
I removed the back of the dryer, removed the single screw holding the fuse in place and checked it for continuity. It didn't work, so I placed an order and 3 days later I was back in business. the replacement took about five minutes.
I guess you could say I went through the process of elemanation, first I replased the thermostat,removed 2 screws pulled off 3 wired with a pair of pliers put them on the new one, still no hot air so I replaced the fuse, took out 1 screw removed 2 wires and placed them on the new fuse, still no hot air, finally I replaced the thermal cut-off switch and WOW that was it hot air was blowing again, the process was very easy I ordered everything from parts slect and they were here the next day, only had to take the back off the dryer with a nut wrench, locate the thernastat, fuse and thermal cut-off which was just above the heating coil I removed 1 screw pulled off 2 wires and place them on the new one. very easy and the repair storys really helped locating the problem
Checked on your website for common problems w/this model dryer,highest probability was the thermal fuse being blown,so I ordered one & checked the vent for being plugged,no problem there,removed the back of the dryer replaced the fuse(very easy to do)put everything back together & started it up...all set now.Thanks for your help
Took the two screws holding the lint trap to top. Used a putty knife to loose the clips holding the top of the dryer up so it could be hindged up for access. Used a nut driver to remove the four screws hold the front door on. Removed the lower dust panel, just clips holding in on. Pull the dryer drum out along with the broken belt and old belt tensioner. Took shop vac and cleaned lint and removed about $2.00 of loose change from the base. Installed the new drum supper wheels. Held belt around drum to put back in. Looped the belt through tensioner and around motor drive pulley as shown in instructions. Put front door on only to find the felt around the door had slipped making the drum hard to turn. Pulled the door back off and laid the dryer on it's back before putting the door back on , so you can run your hand around the door to make sure the felt go inside the drum. Put the four screws back in the door panel before uprighting the dryer. Sucess the drum turned freely. Put other remaining panel and srews in lint trap . Hook the dryer back up to vent, power and gas, and turned on the dryer. Runs like new!
After receiving the part I pulled the dryer out for easy access. Used only a nut driver to remove back cover and the part to replace was easily identified. Then it took a little while to remove all the dust and other particles that had built up over the years. The actual replacement of the part only took a couple of minutes. Reattached the back cover and put back in place. Turned on dryer and I now had heat. Easy fix.
Longest time needed was to determine what cause was. After that ordering part from PartSelect was very easy and saved me money. Part arrived before time given, part was correct and installed without problems.
An online help site lead me to believe the problem was the gas igniter. After ordering that and installing it I discovered that wasn't the problem. I took a look at the schematic which is in the electrical compartment and found that there is more than one thermal breaker. I found the other one, ordered and installed the part and had it running within 30 minutes. I had to access the back of the unit, remove the back cover with a socket wrench, unscrew the thermal breaker and re-install the new one with no special tools.
How I did the repair is of little importance. What is important and impressive is the level of service your company provides. You must have a fantastic system in place and a team who has bought into the concept of providing the best customer service possible. I have been a Manager for over 15 years and would go home proud and would sleep well every night if my team offered the service your team does. Please share this feedback with them and take the time to shake the hand of everyone who was in the chain of service of this order. Smile and tell them Russell C says well done and thank you. Your team made my life easier and I feel appreciated as a customer of your Company.
